User's Manual
Table Of Contents
- Document Reference
- 1 Important Safety instructions
- 2 Introduction to FreeSpeak II™
- 3 Installing a system
- 4 Connecting the Base station
- 4.1 Understanding the Back-Panel Connectors
- 4.2 Connecting to partyline intercom systems
- 4.3 Wireless partyline
- 4.4 Connecting to 4-Wire and digital matrix intercom
- 4.5 Connecting to a program audio source
- 4.6 IFB configuration
- 4.7 Connecting to the stage announce output
- 4.8 Connecting to a PC
- 4.9 Connecting to transceiver/antennas
- 5 Operating the Base station
- 6 Programming a system from the Base station
- 6.1 Introduction
- 6.2 Using the Base station’s programming menus
- 6.3 Saving changes
- 6.4 Changing beltpack labels
- 6.5 Setting and changing port labels
- 6.6 Setting and changing group labels
- 6.7 Adding group members
- 6.8 Beltpacks
- 6.9 Assigning audio routes to a beltpack
- 6.10 Setting the beltpack audio level
- 6.11 Setting beltpack latching
- 6.12 Over the Air (OTA) beltpack registration from the Base station
- 6.13 Setting input and output port levels
- 6.14 Setting port call destination
- 6.15 Configuring a wired partyline
- 6.16 Base station System Menu
- 6.17 System Info
- 6.18 Restoring the Defaults
- 6.19 Antennas
- 6.20 Setting the IP address
- 6.21 Locking front-panel enable buttons
- 6.22 Remote microphone kill
- 6.23 Battery indicator
- 7 Operating the wireless beltpack
- 8 Programming on the beltpack
- 8.1 Introduction to programming on the beltpack
- 8.2 Configuring the beltpack volume settings
- 8.3 Configuring the beltpack headset
- 8.4 Configuring the beltpack microphone
- 8.5 Configuring the beltpack display and LEDs
- 8.6 Configuring the beltpack alarm options
- 8.7 Selecting the beltpack role default set
- 8.8 Selecting the beltpack administration
- 8.9 Setting the listen again option
- 8.10 Accessing beltpack information
- 8.11 Setting display mode
- 8.12 Setting system connect
- 8.13 Enabling over the air (OTA) registration mode from a beltpack
- 8.14 Performing a site survey
- 9 Operating the transceiver/antenna
- 10 FS II Configuration Editor
- 10.1 Loading configurations
- 10.2 Configuration Editor Screen basics
- 10.3 Registering beltpacks using the over the air (OTA) facility
- 10.4 Configuring beltpacks
- 10.4.1 Selecting the beltpack to register or edit
- 10.4.2 Registering beltpacks using the micro USB cable
- 10.4.3 Viewing beltpack registration information
- 10.4.4 Viewing beltpack properties
- 10.4.5 Beltpack audio levels
- 10.4.6 Beltpack alarm options
- 10.4.7 Setting the beltpack role options
- 10.4.8 Assigning beltpack keys
- 10.4.9 Configuring the Reply key
- 10.4.10 Key assignment types
- 10.5 Configuring ports
- 10.6 Configuring groups and wireless partylines
- 10.7 Reducing antenna interference
- 10.8 Configuring IFBs
- 10.9 Configuring Base station system parameters
- 10.10 Diagnostics
- 11 Specifications
- 12 Compliance
4) To confirm the selection and exit the menu screen, press the Menu Select key (D).
8.6.4 Setting the call alert
Use this setting to determine what kind of alert the beltpack issues when it receives an
incoming call. You can set the following alerts:
• Audio warning
• Vibrate
• Audio warning and vibrate
• Off
1) To enter the beltpack menu, press and hold the Menu key.
2) Use the rotary and Menu Select keys to select Settings > Alarm Options > Call
Alert Mode.
3) Use either rotary control to select between:
• Vibrate & Audio (default)
• Vibrate Only
• Audio Only
• Off
4) To confirm the selection and exit the menu screen, press the Menu Select key (D).
8.7 Selecting the beltpack role default set
Use this setting to set the beltpack configuration to the default settings defined in the EHX
configuration map for that role.
1) To enter the beltpack menu, press and hold the Menu key.
2) Use the rotary and Menu Select keys to select Settings > Role Default Set.
3) Use either rotary control to select between:
• On (default)
• Off
4) To confirm the selection and exit the menu screen, press the Menu Select key (D).
8.8 Selecting the beltpack administration
You can select the following administration settings:
• System pairing mode
• Full menu access
84
FreeSpeak II User Guide