User's Manual
Table Of Contents
- Document Reference
- 1 Important Safety instructions
- 2 Introduction to FreeSpeak II™
- 3 Installing a system
- 4 Connecting the Base station
- 4.1 Understanding the Back-Panel Connectors
- 4.2 Connecting to partyline intercom systems
- 4.3 Wireless partyline
- 4.4 Connecting to 4-Wire and digital matrix intercom
- 4.5 Connecting to a program audio source
- 4.6 IFB configuration
- 4.7 Connecting to the stage announce output
- 4.8 Connecting to a PC
- 4.9 Connecting to transceiver/antennas
- 5 Operating the Base station
- 6 Programming a system from the Base station
- 6.1 Introduction
- 6.2 Using the Base station’s programming menus
- 6.3 Saving changes
- 6.4 Changing beltpack labels
- 6.5 Setting and changing port labels
- 6.6 Setting and changing group labels
- 6.7 Adding group members
- 6.8 Beltpacks
- 6.9 Assigning audio routes to a beltpack
- 6.10 Setting the beltpack audio level
- 6.11 Setting beltpack latching
- 6.12 Over the Air (OTA) beltpack registration from the Base station
- 6.13 Setting input and output port levels
- 6.14 Setting port call destination
- 6.15 Configuring a wired partyline
- 6.16 Base station System Menu
- 6.17 System Info
- 6.18 Restoring the Defaults
- 6.19 Antennas
- 6.20 Setting the IP address
- 6.21 Locking front-panel enable buttons
- 6.22 Remote microphone kill
- 6.23 Battery indicator
- 7 Operating the wireless beltpack
- 8 Programming on the beltpack
- 8.1 Introduction to programming on the beltpack
- 8.2 Configuring the beltpack volume settings
- 8.3 Configuring the beltpack headset
- 8.4 Configuring the beltpack microphone
- 8.5 Configuring the beltpack display and LEDs
- 8.6 Configuring the beltpack alarm options
- 8.7 Selecting the beltpack role default set
- 8.8 Selecting the beltpack administration
- 8.9 Setting the listen again option
- 8.10 Accessing beltpack information
- 8.11 Setting display mode
- 8.12 Setting system connect
- 8.13 Enabling over the air (OTA) registration mode from a beltpack
- 8.14 Performing a site survey
- 9 Operating the transceiver/antenna
- 10 FS II Configuration Editor
- 10.1 Loading configurations
- 10.2 Configuration Editor Screen basics
- 10.3 Registering beltpacks using the over the air (OTA) facility
- 10.4 Configuring beltpacks
- 10.4.1 Selecting the beltpack to register or edit
- 10.4.2 Registering beltpacks using the micro USB cable
- 10.4.3 Viewing beltpack registration information
- 10.4.4 Viewing beltpack properties
- 10.4.5 Beltpack audio levels
- 10.4.6 Beltpack alarm options
- 10.4.7 Setting the beltpack role options
- 10.4.8 Assigning beltpack keys
- 10.4.9 Configuring the Reply key
- 10.4.10 Key assignment types
- 10.5 Configuring ports
- 10.6 Configuring groups and wireless partylines
- 10.7 Reducing antenna interference
- 10.8 Configuring IFBs
- 10.9 Configuring Base station system parameters
- 10.10 Diagnostics
- 11 Specifications
- 12 Compliance
1) From the Name list, select the beltpack.
2) From the Reply key list, select REPLY.
To assign a call destination:
3) From the Name list, select the beltpack.
4) From the Reply key list, select a destination from the drop-down list.
To deactivate the REPLY key:
5) From the Name list, select the beltpack.
6) From the Reply key list, select ----.
10.4.10 Key assignment types
By default an assignment is talk only; however 4-wire and partyline inputs can be selected as
the following:
• Listen. The caller can be heard, but no outgoing audio path is created when the key
is pressed.
• Talk and listen (Talk&List). An outgoing and incoming audio path is created when
the key is pressed.
• Dual talk and listen (Dual T&L). A short press produces a latching listen path, while
a long press produces a momentary talk.
• Forced listen (Frc L). Assigning a key in this way forces a permanent listen path -
that is the remote source can be heard on the beltpack even when the key is not
latched on. No talk path is created when the key is pressed. This is useful for
monitoring a program input or directors feed.
• Talk and forced listen (T&F L). This is the same as a Forced Listen key, except a
talk path is created when the key is pressed.
• Talk. The key will only create an outgoing audio path when pressed.
The type of a key is indicated on the beltpack with the use of different cases for the label: a
Talk key is shown in all capitals, for example TEST. A listen key is shown in all lower-case, for
example test. Dual Talk and Listen, and Talk and Forced Listen keys are indicated by an
initial capital, with the rest in lower case, for example Test.
10.5 Configuring ports
From the Configuration Editor, you can use the Ports tab to:
• Select, name and configure ports
• Set the input output and VOX levels for ports
111
FreeSpeak II User Guide