User's Manual
Table Of Contents
- Document Reference
- 1 Important Safety instructions
- 2 Introduction to FreeSpeak II™
- 3 Installing a system
- 4 Connecting the Base station
- 4.1 Understanding the Back-Panel Connectors
- 4.2 Connecting to partyline intercom systems
- 4.3 Wireless partyline
- 4.4 Connecting to 4-Wire and digital matrix intercom
- 4.5 Connecting to a program audio source
- 4.6 IFB configuration
- 4.7 Connecting to the stage announce output
- 4.8 Connecting to a PC
- 4.9 Connecting to transceiver/antennas
- 5 Operating the Base station
- 6 Programming a system from the Base station
- 6.1 Introduction
- 6.2 Using the Base station’s programming menus
- 6.3 Saving changes
- 6.4 Changing beltpack labels
- 6.5 Setting and changing port labels
- 6.6 Setting and changing group labels
- 6.7 Adding group members
- 6.8 Beltpacks
- 6.9 Assigning audio routes to a beltpack
- 6.10 Setting the beltpack audio level
- 6.11 Setting beltpack latching
- 6.12 Over the Air (OTA) beltpack registration from the Base station
- 6.13 Setting input and output port levels
- 6.14 Setting port call destination
- 6.15 Configuring a wired partyline
- 6.16 Base station System Menu
- 6.17 System Info
- 6.18 Restoring the Defaults
- 6.19 Antennas
- 6.20 Setting the IP address
- 6.21 Locking front-panel enable buttons
- 6.22 Remote microphone kill
- 6.23 Battery indicator
- 7 Operating the wireless beltpack
- 8 Programming on the beltpack
- 8.1 Introduction to programming on the beltpack
- 8.2 Configuring the beltpack volume settings
- 8.3 Configuring the beltpack headset
- 8.4 Configuring the beltpack microphone
- 8.5 Configuring the beltpack display and LEDs
- 8.6 Configuring the beltpack alarm options
- 8.7 Selecting the beltpack role default set
- 8.8 Selecting the beltpack administration
- 8.9 Setting the listen again option
- 8.10 Accessing beltpack information
- 8.11 Setting display mode
- 8.12 Setting system connect
- 8.13 Enabling over the air (OTA) registration mode from a beltpack
- 8.14 Performing a site survey
- 9 Operating the transceiver/antenna
- 10 FS II Configuration Editor
- 10.1 Loading configurations
- 10.2 Configuration Editor Screen basics
- 10.3 Registering beltpacks using the over the air (OTA) facility
- 10.4 Configuring beltpacks
- 10.4.1 Selecting the beltpack to register or edit
- 10.4.2 Registering beltpacks using the micro USB cable
- 10.4.3 Viewing beltpack registration information
- 10.4.4 Viewing beltpack properties
- 10.4.5 Beltpack audio levels
- 10.4.6 Beltpack alarm options
- 10.4.7 Setting the beltpack role options
- 10.4.8 Assigning beltpack keys
- 10.4.9 Configuring the Reply key
- 10.4.10 Key assignment types
- 10.5 Configuring ports
- 10.6 Configuring groups and wireless partylines
- 10.7 Reducing antenna interference
- 10.8 Configuring IFBs
- 10.9 Configuring Base station system parameters
- 10.10 Diagnostics
- 11 Specifications
- 12 Compliance
10.4.7 Setting the beltpack role options
Use this option to determine the beltpack role options.
Setting the display brightness
Use this option to adjust the display brightness.
• From the Display Brightness list, select a display brightness from 1 to 5.
Note: The factory default is 5.
Setting when the screen automatically dims
The beltpack display will dim if no key is used or there is no incoming call or call alert after a
certain timeout period. To determine the timeout period:
• From the Display Dim Timeout list, select a timeout period. The settings run from
Off to 120 seconds. The factory default is 30 seconds.
Setting when the screen automatically turns off
The beltpack display will turn off if no key is used or there is no incoming call or call alert after
a certain timeout period. To determine this threshold period:
• From the Display Off Timeout list, select a timeout period. The settings run from Off
to 120 seconds. The factory default is 30 seconds.
Setting when the listen again auto is automatically deleted
You can configure the beltpack to automatically record incoming audio to allow you to replay
the audio. These recordings are automatically deleted after a certain period. To determine this
period:
• From the Listen Again Auto Delete list, select a timeout period. The settings run
from Off to 240 minutes. The factory default is 240 minutes.
Setting the listen again recording time
You can configure the beltpack to automatically record incoming audio to allow you to replay
the audio. To determine the recording period:
• From the Listen Again Record Time, select a recording time. The settings run from
0 seconds to 15 seconds. The factory default is 15 seconds.
Setting the Reply Tally Auto Clear time
Menu Level
Use this option to determine what menu options are available to beltpack users.
From the Menu list, select from the following settings:
• Advanced- all menu options are available.
• Normal – all menu options are available except:
o Main > Volume Operation
108
FreeSpeak II User Guide