User's Manual
Table Of Contents
- Document Reference
- 1 Important Safety instructions
- 2 Introduction to FreeSpeak II™
- 3 Installing a system
- 4 Connecting the Base station
- 4.1 Understanding the Back-Panel Connectors
- 4.2 Connecting to partyline intercom systems
- 4.3 Wireless partyline
- 4.4 Connecting to 4-Wire and digital matrix intercom
- 4.5 Connecting to a program audio source
- 4.6 IFB configuration
- 4.7 Connecting to the stage announce output
- 4.8 Connecting to a PC
- 4.9 Connecting to transceiver/antennas
- 5 Operating the Base station
- 6 Programming a system from the Base station
- 6.1 Introduction
- 6.2 Using the Base station’s programming menus
- 6.3 Saving changes
- 6.4 Changing beltpack labels
- 6.5 Setting and changing port labels
- 6.6 Setting and changing group labels
- 6.7 Adding group members
- 6.8 Beltpacks
- 6.9 Assigning audio routes to a beltpack
- 6.10 Setting the beltpack audio level
- 6.11 Setting beltpack latching
- 6.12 Over the Air (OTA) beltpack registration from the Base station
- 6.13 Setting input and output port levels
- 6.14 Setting port call destination
- 6.15 Configuring a wired partyline
- 6.16 Base station System Menu
- 6.17 System Info
- 6.18 Restoring the Defaults
- 6.19 Antennas
- 6.20 Setting the IP address
- 6.21 Locking front-panel enable buttons
- 6.22 Remote microphone kill
- 6.23 Battery indicator
- 7 Operating the wireless beltpack
- 8 Programming on the beltpack
- 8.1 Introduction to programming on the beltpack
- 8.2 Configuring the beltpack volume settings
- 8.3 Configuring the beltpack headset
- 8.4 Configuring the beltpack microphone
- 8.5 Configuring the beltpack display and LEDs
- 8.6 Configuring the beltpack alarm options
- 8.7 Selecting the beltpack role default set
- 8.8 Selecting the beltpack administration
- 8.9 Setting the listen again option
- 8.10 Accessing beltpack information
- 8.11 Setting display mode
- 8.12 Setting system connect
- 8.13 Enabling over the air (OTA) registration mode from a beltpack
- 8.14 Performing a site survey
- 9 Operating the transceiver/antenna
- 10 FS II Configuration Editor
- 10.1 Loading configurations
- 10.2 Configuration Editor Screen basics
- 10.3 Registering beltpacks using the over the air (OTA) facility
- 10.4 Configuring beltpacks
- 10.4.1 Selecting the beltpack to register or edit
- 10.4.2 Registering beltpacks using the micro USB cable
- 10.4.3 Viewing beltpack registration information
- 10.4.4 Viewing beltpack properties
- 10.4.5 Beltpack audio levels
- 10.4.6 Beltpack alarm options
- 10.4.7 Setting the beltpack role options
- 10.4.8 Assigning beltpack keys
- 10.4.9 Configuring the Reply key
- 10.4.10 Key assignment types
- 10.5 Configuring ports
- 10.6 Configuring groups and wireless partylines
- 10.7 Reducing antenna interference
- 10.8 Configuring IFBs
- 10.9 Configuring Base station system parameters
- 10.10 Diagnostics
- 11 Specifications
- 12 Compliance
• When using AA Batteries follow all safety instructions from manufacturer. Do not mix
different battery chemistries. When depleted, replace all batteries.
• The in-beltpack USB charging feature has only been tested utilizing USB2.0 port.
Warning: To reduce the risk of fire or electric shock, do not expose this product to rain or
moisture.
1.1 Safety symbols
Familiarize yourself with the safety symbols in Figure 1: Safety symbols. These symbols are
displayed on the apparatus and warn you of the potential danger of electric shock if the
system is used improperly.
Figure 1-1: Safety symbols
Note: For compliance notices, see 12 Compliance.
10
FreeSpeak II User Guide