Installation Guide

ManualsBrandsHM Electronics ManualsComputers & AccessoriesBase Station

Fig. 2.3

6. Install any other components required for func-

tionality such as speakers, etc. If installing a new

system with Speaker/Mic SM7000 use Fig. 2.3 as

a wiring reference.

However, if connecting to an existing system us-

ing a microphone or speaker that is not a NEXEO

component such as a DM5 microphone, or SP10

speaker, you must also use the IB7000 to make

these components compatible. Use Fig. 3.1 as a

wiring reference and see “Component Notes.”

7. Route and terminate all additional component

cables to the Base Station using the wiring refer-

ences in this guide. Consult the store’s IT person-

nel when connecting to the network router.

8. Terminate the Base Station power supply and

connect to outlet. The Base Station turns on.

9. On the Base Station UI, follow the onscreen In-

stallation Wizard to configure and test the system.

Fig. 2.1

Note: If you accidentally exit the Installation Wiz-

ard and need to return to it. LOG IN to the system,

go to

SYSTEM, then the ADVANCED tab and select

“Installation” from the drop-down menu. Tap the

“Start Installation Wizard” button.

10. Critical Step: The Installation Wizard prompts

you to use a paired headset switched into Recep-

tion Location Mode. You will need to walk all ar-

eas of the store where the headset will be used to

ensure a good and continuous signal. The Boom

LED at the tip of the Headset microphone flashes

different colors to indicate areas with strong or

weak reception. This color-coded range is shown

in Fig. 2.2.

Reception/Signal

Strength

NEXEO Headset

Boom LED

VERY STRONG

STRONG

MODERATE

WEAK

NO SIGNAL

Re-pair the Headset if there

are no colors on the Boom LED

Fig. 2.2

Note: Depending on the size and layout of the

store, some stores may require more than one

Remote Transceiver to provide good coverage.

11. Test audio levels between the headsets and the

drive-thru ordering points, adjust accordingly

using the volume controls on the Base Station UI

12. Once the optimal location for the Remote Trans-

ceivers has been verified. Secure all the loosely

mounted system components.

Remote

XCVR 4

Remote

XCVR 3

Remote

XCVR 2

Remote

XCVR 1

Ethernet

DC +

DC -

GND

Micro

USB

J200

J600

J201 J800 J801

J802

J805

J804

J803

J2003

J3000

J4501 J4500

J1400

J3200

J3400

J3600

J3800

1 1 1

Serial

Debug

USB

J?301

J?300

RELAY |

LOOPPLC

BCKP

SPKR

1 2 3 1 2

1 2 3 4 5

BK SPKR (+) - 5

BK SPKR (-) - 4

NO - 3

COM - 2

NC -1

POS - 1

NEG - 2

IN 1 - 1

IN 2 - 2

GND- 3

HME

SM7000

SPEAKER/MIC REAR VIEW

LOOP

CONNECTION

1 2 3

BK SPKR (+) - 5

BK SPKR (-) - 4

NO - 3

COM - 2

NC -1

POS - 1

NEG - 2

IN 1 - 1

IN 2 - 2

GND- 3

HME

1 2

3 4

Base Station

opened

PCBA

To NETWORK ROUTER

For CLOUD CONNECTION

48 V

BASE STATION

POWER SUPPLY

To REMOTE

TRANSCEIVER REAR

SM7000

SPEAKER/MIC REAR VIEW

LOOP

CONNECTION

RT7000 TRANSCEIVER

Front View

NOTE: Shield

must be

terminated

to GND

This Way

DC+ GND DC-

13. Use cable ties to bundle and strain relief the ca-

bles exiting the Base Station to one of the cross-

bars on the rear housing.

14. Close the Base Station. The system is now ready

for use.

1 2 3 4

HME

WALL OUTLETAC70 BATTERY CHARGER

Front/Top View

POWER ADAPTER

Note: Only use the HME approved Power Adapter provided

Charging

Ports (x4)

on top

Storage

Ports (x4)

on side