USER MANUAL ULTRASLIM PAINTABLE 550 WATT PANEL HEATER WITH SMART APP EPPH5W Thank you for choosing electriQ Please read the manual before using this heater and keep it safe for future reference. Visit our page www.electriQ.co.
CONTENTS SAFETY INSTRUCTIONS 3 PRODUCT OVERVIEW 6 INSTALLATION 5 OPERATION 7 SETTING UP THE APP 8 USING THE APP 13 CLEANING AND MAINTENANCE 18 TROUBLESHOOTING 18 TECHNICAL SPECIFICATIONS 19 SUPPORT 19 PRODUCT FICHE 20 2
SAFETY INSTRUCTIONS IMPORTANT • Carefully read the instructions before operating the unit • This appliance is for indoor use only. • Rating: This unit must be only connected to a 220-240 V / 50 Hz earthed outlet. • Installation must be in accordance with regulations of the country where the unit is used. • If you are in any doubt about the suitability of your electrical supply have it checked and, if necessary, modified by a qualified electrician. • This heater has been tested and is safe to use.
• Never use the plug as a switch to start and turn off the heater. Use the provided power button located on the control panel. • Do not use an external timer. • Do not cover the appliance, or place items close to the unit which may restrict airflow, as this may present a fire risk. • The heater must not be located immediately below a socket outlet. • Always place the unit on a dry and stable surface. Do not move or tilt the unit. • Avoid keeping the unit in direct sunlight for a long period of time.
WALL MOUNTING INSTRUCTIONS Unpack your heater, do not use a sharp object as this may damage the heater. Mark the positions of the four holes to be drilled on the wall. (Install the heater at a minimum of 20cm above the floor.) Use a spirit level to ensure that all the holes are level. Drill the 4 holes with a suitable drill bit for the type of wall. Insert the plastic wall fittings into the holes. Hold the heater in position against the wall fittings inserted in the previous step.
FREE STANDING Secure the provided feet to the base of the heater using the screws provided. CONTROL PANEL Check the heater to be sure it is not damaged.
OPERATION Connect the power and turn on using the switch on the side of product. Press the standby button once and the "ON" indicator on the LCD screen will illuminate, the unit will now be powered ON set to the default desired room temperature of 25°C. SETTING THE DESIRED TEMPERATURE Press the SET button and the temperature setting indicator will flash, then use the temperature UP and DOWN buttons to adjust the temperature.
CONNECTING THE APPLIANCE TO WIFI DOWNLOAD THE APP TO YOUR PHONE Download the” TUYA SMART” app, from your chosen app store, using the QR codes below, or by searching for the app in your chosen store. Android IOS MODES AVAILABLE FOR SETUP The heater has two different setup modes, Quick Connection and AP (Access Point). The quick connection is a quick and simple way to set the unit up. The AP connection uses a direct local WiFi connection between your phone and the heater to upload the network details.
REGISTER THE APP 1. Press on the register button at the bottom of the screen. 4. A verification code will be sent by the method selected in step 3. Enter the code into the app. 2. Read the Privacy policy and press the Agree Button. 5. Type in the password you would like to create. This needs to be 6-20 characters, with letters and numbers. 9 3. Enter your email address or phone number and press continue to register. 2. The app is now registered.
SETTING UP YOUR HOME WITHIN THE APP TUYA is designed so it can work with a large number of compatible smart devices within your home. It can also be set up to work with multiple devices within different houses as such during the setup process, the app requires that different areas are created and named to allow easy management of all your devices. When new devices are added, they are assigned to one of the rooms you have created. CREATING ROOMS 1. Press on the ADD HOME button. 3.
CONNECTING USING THE QUICK CONNECTION METHOD Before initiating the connection, make sure the WiFi indicator is flashing twice per second. If not follow the instructions for changing the connection mode. Also ensure your phone is connected to the WiFi network. (We advise turning mobile data off during setup) 1. Open app and press “+” to add device, or use the add device button 4. Enter your Wi-Fi password and press confirm. 2. Select the type of device as “Heater” within the Home Appliance tab. 5.
CONNECTING USING AP MODE (ALTERNATIVE METHOD) Before initiating the connection, make sure the unit is in standby mode, with the WiFi Indicator flashing once per second. If not follow the instructions for changing the WiFi connection mode. Also ensure your phone is connected to the WiFi network. (We advise turning mobile data off during setup) 1. Open app and press “+” to add device, or use the add device button 4.
CONTROLLING YOUR APPLIANCE THROUGH THE APP THE HOME SCREEN NOTE: Due to continuous development of the app, the layout and available features may be subject to change. Each device has its own entry on the home screen to allow the user to either quickly turn the unit on or off, or to enter the device screen to make other changes. Voice Control: Press to give verbal instructions for operation. Add Device: Add a device to the app, and go through the setup process.
DEVICE SCREEN The device screen is the main control screen for the heater, providing access to the controls to amend the functions and settings. Back: Returns to the Home Screen Device Name Edit Name: Use to change the name of the heater Desired Temperature: Displays what has been set as the target room temperature. Current Temperature: Displays what the current temperature is.
SMART SCENES Smart Scenes is a powerful tool providing the option to customize the operation of the air heater based both on conditions within the room and outside influences. This gives the user the option of specifying much more intelligent actions. These are split into two categories Scene and Automation. SCENE Scene allows for a one touch button to be added to the Home Screen. The button can be used to change a number of settings in one go, and can change all the settings within the unit.
AUTOMATION Automation allows an automatic action to be set up for the device. This can be triggered by the Time, and a range of other influences, depending what other TUYA enabled devices you have on the network. 1. Press on the Scene tab at the bottom of the Home screen 2. Press on the Automation tab at the top of the screen. 3. Press on the + at the top of the screen or press on Add Automatic Action 4.
PROFILE TAB The profile tab gives you the option to edit both your detail, and use the added features of the unit. HOME MANAGEMENT Home Management proves options for managing your TUYA account, giving options such as adding a home, adding and removing rooms, and sharing devices with family.
CLEANING AND MAINTENANCE ATTENTION: Please shut off the unit and unplug from the mains before cleaning or performing any maintenance. CLEANING THE SURFACE • Clean the heater with a duster or a soft wet cloth. Do not use chemical solvents (such as benzene, alcohol or gasoline) as they may cause irreversible damage. Make sure no water enters the control panel or gaps in the casing. • Do not run the unit until completely dry.
electriQ UK SUPPORT www.electriQ.co.uk/support Please, for your own convenience, make these simple checks before calling the service line. If the unit still fails to operate call: 0330 390 3061or complete the online form 1. Is the unit plugged into the mains? 2. Is the fuse OK? 3. Switch the unit off and wait three minutes to see if the issue is resolved. Restart the unit. Office hours: 9AM - 5PM Monday to Friday www.electriQ.co.
Model Identifier: EPPH5W Item Symbol Value Unit Heat Output Item Unit Type of heat input, for electric storage local space heaters only (select one) Nominal heat output Pnom 0.55 kW manual heat charge control, with integrated thermostat No Minimal heat output Pmin 0 kW manual heat charge control with room and/or outdoor temperature feedback No Maximum continuous heat output Pmax 0.
