User Guide

ManualsBrandsHK INSTRUMENTS ManualsOtherHK INSTRUMENTS SIRO-MOD Indoor Air Quality Transmitters

User Guide

Indoor air quality transmitters

Siro & Siro-MOD

This document contains informaon about conguring and using Siro

indoor air quality transmier. Before reading this guide, check that the

transmier has been installed according to the installaon instruc-

ons.

Siro is available with several oponal air quality sensors. The modu-

lar device can be equipped with CO

concentraon and VOC (Vola-

le Organic Compounds) measurements or alternavely PM (Parcu-

late Maer) measurement, and in addion temperature and humidity

measurements. Siro is available with a user interface that includes an

LCD display and three pushbuons. The device is always equipped

with voltage outputs, and oponally with Modbus communicaon and

current outputs.

Introduction

ScHematics

–

Air ow aperture

Display

Pushbuon + (up/increase)

Pushbuon OK (choose/conrm)

Pushbuon – (down/decrease)

Lid opening buon

Opening for the wires

Navigating the menu

The device's physical interface includes a display and three pushbuons.

By using the user interface, it is possible to choose the desired measurement values on the display and to adjust the sengs of the device.

Note that when the menu locking jumper is installed, it is not possible to open the menu and the display will not react when pressing

the buon. Please see the installaon instrucons for more details about the locking jumper.

The buon funcons:

–

Scroll up in the menu / increase the value

Scroll down in the menu / decrease the value

Open the menu / conrm (press shortly) / go back to the basic view (keep the buon down/press longer)

The use and conguraon of Siro is simple and easy by following this

guide describing a Siro device with a display (-D).

Please note that this guide includes all measurement opons. The

device menu only shows the opons that have been chosen to that

parcular device. You can nd more informaon about the measur-

ment opons in the end of this document.

Summary of content (8 pages)

PAGE 1
Indoor air quality transmitters Siro & Siro-MOD User Guide Introduction This document contains information about configuring and using Siro indoor air quality transmitter. Before reading this guide, check that the transmitter has been installed according to the installation instructions. Siro is available with several optional air quality sensors.
PAGE 2
Page 2 Display values Celsius Fahrenheit CO2 Humidity CO2 EQ IAQ PM2.5 hour PM10 hour Exit Modbus Brightness Display values Menu stRucture [ [ [ [ [ [ [ [ ] ] ] ] ] ] ] ] Brightness Modbus Address Baudrate Parity Exit Oﬀset Outputs Outputs Out1 Out2 Out3 Out4 Exit Offset Celsius Fahrenheit CO2 Humidity TVOC ppm CO2 EQ TVOC ug/m3 PM Exit () () () () () () () () () () () () 1/6 Option 1, Option 2, Option 3, Option 4 ...
PAGE 3
Page 3 Step 1: Choosing the measurement values on the display Step 1.1: Display view The basic view on the display is scaled based on how many measurement values have been chosen to be viewed on the display. 1-4 measurement values can be shown simultaneously (see figure 1a). If five or more values are selected, the measurements are shown one by one and the view changes every 10 seconds. Individual measurements can be scrolled in the basic view with + and – buttons.
PAGE 4
Page 4 Step 2: Brightness control This adjusts the brightness of the display in stand-by mode. The brightness of the display is always at the maximun level when the buttons are used. 1) Press OK to enter the settings menu. Figure 2a 2) Choose Brightness. Settings Display values Brightness Modbus + OK – Figure 2b 3) Adjust the brightness. • Increase/decrease the brightness by pressing and – . + Brightness + OK – 4) Saving the chosen brightness level and exiting.
PAGE 5
Page 5 Step 4: Outputs The device includes four freely configurable outputs. Current (optional) or voltage output can be chosen for each of them. The output signal has to be chosen first with a jumper (see the installation instructions), after which the output settings can be changed in the Outputs menu. 1) Press OK to enter the settings menu. Figure 4a 2) Choose Outputs. Settings Brightness Modbus Outputs + OK – Figure 4b 3) Choose measurement, scale and limits for each output.
PAGE 6
Page 6 Outputs continued Table 1 - Output limits Measurement Celsius 1* Fahrenheit 1* CO2 Default limits Adjustable low limit Adjustable high limit Smallest range available 0.0...50.0 °C 0.0...45.0 °C 5.0...50.0 °C 5.0 °C 32...122 °F 32...113 °F 41...122 °F 9 °F 400...2000 ppm 0...1900 ppm 500…2000 ppm 100 ppm 0.0…100.0 % 0.0…90.0 % 10.0…100.0 % 10.0 % TVOC ppm 0.00…30.00 ppm 0.00…28.00 ppm 2.00…30.00 ppm 2.00 ppm CO2 EQ 400...2000 ppm 0...
PAGE 7
Page 7 Offset Continued Table 2 - Offset limits Measurement Limit Celsius 1* ±5.0 °C ±9.0 °F Fahrenheit 1* ±200 ppm CO2 ±10.0 % Humidity TVOC ppm ±3.00 ppm CO2 EQ ±200 ppm ±1000 µg/m3 TVOC ug/m3 2* 0.30…2.00 (offset multiplier) PM 3* 1*) Celsius and Fahrenheit limits are interdependent, and thus a change in one limit of a measurement will also change the limits of the other measurement. 2*) TVOC µg/m3 offset will also affect the IAQ value based on TVOC.
PAGE 8
Page 8 Information about the measurements Table 3 - Additional information about the measurements Measurement Text in the Siro user interface Description Unit T (Temperature) Celsius Temperature ⁰C Fahrenheit Temperature ⁰F rH (Relative humidity) Humidity Relative humidity %rH CO2 (Carbon dioxide) CO2 Carbon dioxide concentration ppm VOC (Volatile Organic Compounds)* TVOC ppm Total concentration of organic volatile compounds ppm TVOC ug/m3 Total concentration of organic volatile com