Owner manual

25
EasyCub Parts List
Part No. Description Material Dimensions
No. off
1 1 Building instructions Paper, 80 g/m² A4
2 1 Decal set Printed adhesive film 500 x 700 mm
3 1 L.H. fuselage shell Moulded Elapor foam Ready made
4 1 R.H. fuselage shell Moulded Elapor foam Ready made
5 1 Canopy Moulded Elapor foam Ready made
6 1 L.H. wing panel Moulded Elapor foam Ready made
7 1 R.H. wing panel Moulded Elapor foam Ready made
8 1 Tailplane Moulded Elapor foam Ready made
9 1 Fin Moulded Elapor foam Ready made
70 1 Main undercarriage unit Spring steel 2.5 mm Ø, ready made
Small items
20 3 Velcro tape, “mushroom” Plastic 25 x 60 mm
21 3 Velcro tape, “felt” Plastic 25 x 60 mm
22 2 Canopy latch Inj. moulded plastic Ready made
23 2 Canopy latch tongue Inj. moulded plastic Ready made
24 1 Glue-fitting control surface horn Inj. moulded plastic Ready made
25 2 Swivel pushrod connector Metal Ready made, 6 mm Ø
26 2 Washer Metal M2
27 2 Nut Metal M2
28 2 Socket-head grubscrew Metal M3 x 3 mm
29 1 Allen key Metal 1.5 mm A/F
30 1 Front spar holder, “tall” Inj. moulded plastic Ready made
31 1 Rear spar holder, “low”` Inj. moulded plastic Ready made
32 2 Screw Inj. moulded plastic M5 x 50 mm
33 2 Wing screw support, part A Inj. moulded plastic Ready made, M5
34 2 Wing screw support, part B Inj. moulded plastic Ready made, M5
35 1 Glue-fitting horn, tailskid Inj. moulded plastic Ready made
36 1 Glue-fitting tailskid bush Inj. moulded plastic Ready made
37 2 Motor mount Inj. moulded plastic Ready made
38 1 Motor bulkhead Inj. moulded plastic Ready made
39 4 Motor bulkhead adjustor screw Metal M3 x 10 mm
40 2 Motor bulkhead mounting screw Metal M3 x 16 mm
Wire and rod
50 2 Tubular wing spar GRP tube 8 Ø x 6 Ø x 400 mm
51 2 Tubular wing spar GRP tube 8 Ø x 6 Ø x 100 mm
52 2 Pre-formed elevator pushrod Metal 0.8 Ø x 510 mm
53 2 Pre-formed rudder pushrod Metal 0.8 Ø x 510 mm
54 1 Elevator snake outer sleeve Plastic 3 Ø x 2 Ø x 480 mm
55 1 Rudder snake outer sleeve Plastic 3 Ø x 2 Ø x 480 mm
56 1 Elevator snake inner sleeve Plastic 2 Ø x 1 Ø x 500 mm
57 1 Rudder snake inner sleeve Plastic 2 Ø x 1 Ø x 500 mm
Undercarriage set
71 2 Lightweight main wheel Plastic 53 Ø
72 4 Wheel collet Metal 2.7 Ø x 8 Ø x 5 mm
73 4 Socket-head grubscrew Metal M3 x 3 mm
74 1 Undercarriage bracket Plastic Ready made
75 1 Undercarriage retainer screw Metal M3 x 12 mm
76 1 Tailwheel unit Metal 1.3 mm Ø
77 1 Lightweight tailwheel Foam rubber 26 mm Ø
78 2 Tailwheel retainer sleeve Tubular rivet 2 Ø x 0.2 x 3 mm