X4 AC Pro AC/DC 4 Port Multicharger Manual

2524
NiMH / NiCd Battery Program (cont.)
............................
BATTERY CHECK
Program Start
Press and hold the START START/ENTER button until
you see “BATTERY CHECK...” the battery should then
begin charging.
Once charging has started the screen will display the
battery type, charge rate, total pack voltage, elapsed
time, and total current fed in mAh.
Once the battery is fully charged, the screen will read “END: FINISHED” and the
charger will emit a chiming sound. You can press the ■ button at any time during the
charging process to stop charging.
NiMH 1.3A 6.00V
CHG 009:11 00411
66
NiMH / NiCd Auto Charge Mode
In this mode, the charger automatically detects the connected NiMH or NiCd
battery and determines the proper full charge and cuto thresholds. Setting the
upper charge current limit for safe levels based on your battery speci cations
will ensure safe charging of your speci c battery. If you are unsure of the
maximum allowable charge rates, set the charger to a maximum of 1C (battery
mAh/1000, i.e., 2500mAh = 2.5A).
After selecting the correct battery type use the INC
and DEC to scroll to Auto CHARGE Mode. Press the
START/ENTER button to con rm.
Setting the Charge Current
Press INC and DEC to increase or decrease the charge
current. Press the START/ENTER button to con rm the
setting. The rate can be adjusted from 0.1 ~ 10A.
Program Start
Press and hold the START START/ENTER button until you see “BATTERY
CHECK...” the battery should then begin charging.
Once the battery is fully charged, the screen will read “END: FINISHED” and the
charger will emit a chiming sound. You can press the ■ button at any time during the
charging process to stop charging.
CURRENT 2.0A
NiMH Auto CHARGE
CURRENT 2.0A
NIMH CHARGE
NiMH / NiCd Battery Program (cont.)
NiMH / NiCd Discharge Mode
After selecting the correct battery type use the INC
and DEC to scroll to DISCHARGE Mode. Press the
START/ENTER button to con rm.
Setting the Discharge Current
Press INC and DEC to increase or decrease the charge
current. Press the START/ENTER button to con rm the
setting. The rate can be adjusted from 0.1 ~ 2.0A.
Setting the Cut-O Voltage
Press INC and DEC to increase or decrease the cut-o
voltage Press the START/ENTER button to con rm the
setting.
Make sure to follow the instructions provided with your battery
when setting the voltage cuto . The X4 AC Pro will stop discharging
when the battery has reached the preset voltage cuto .
Program Start
Press and hold the START START/ENTER button until you see “BATTERY
CHECK...” the battery should then begin discharging.
Once discharging has commenced, the charger will
display the following information: battery type, dis-
charging current, battery voltage, discharging time and
discharged capacity.
When discharging is complete, the screen will read “END:CUTOFF-VOL” and the
charger will emit a ringing sound. The charger will display the elapsed time, end
voltage and the discharged capacity in mAh. You can press the ■ button at any time
during the charging process to stop charging.
NiMH / NiCd Re-Peak Mode
Applicable to NiMH and NiCD batteries only, in re-peak mode the charger can
peak charge the battery once, twice, or three times in a row automatically. This
process is good for con rming the battery is fully charged and for verifying how
well the battery can accept a fast charge. A  ve-minute cool-down delay occurs
after each re-peak charge.
CURRENT 2.0A
NiMH DISCHARGE
1.0A CUT: 3.2V
NIMH DISCHARGE
1.0A CUT: 3.2V
NIMH DISCHARGE
Caution
NiMH 1.3A 4.90V
DCH 003:44 00450
66