User Manual

2726
NiMH / NiCd Battery Program (cont.)
IN REPEAK MODE, THE X4 AC PRO USES THE CHARGE AMPERAGE
AND VOLTAGE SETTINGS ENTERED IN CHARGE MODE SEE PAGE 20.
Note
After selecting the correct battery type, use the INC or
DEC buttons to select the “RE-PEAK” mode. Press the
START/ENTER button to con rm.
The number of Re-Peak cycles will begin  ashing use
the INC or DEC buttons to select the number of Re-
peak cycles you want to perform up to 3 total cycles.
Program Start
Press and hold the START START/ENTER button until you see “BATTERY
CHECK...” the battery should then begin Re-Peak charging.
Once Re-Peak process has begun, the charger will
display the following real-time information: battery
type, charging current, battery voltage, elapsed time
and charged capacity.
Once the Re-Peak process has completed, the screen will read “END: RE-PEAK”
and the charger will emit a chiming sound. The X4 AC Pro will display the
charge/discharge capacity for each cycle. Using the + and - buttons, you can
scroll through this data for each cycle.
NiCD/NiMH Cycle Mode
The X4 AC Pro makes cycling of NiCD/NiMH batteries easy. The process of
discharging and recharging (cycling) can be achieved automatically with one
simple step and will improve the performance of NiCD/NiMH batteries. We
strongly recommend cycling any battery that has been discharged and stored
for a period of time. This will increase battery life and improve performance.
FOR CYCLING, THE X4 AC PRO USES THE CHARGE/DISCHARGE AMPERAGE
AND VOLTAGE SETTINGS ENTERED IN THE CHARGE AND DISCHARGE
MODES SEE PAGES 20 ~ 22.
After selecting the correct battery type use the INC
and DEC to scroll to CYCLE Mode. Press the START/
ENTER button to con rm.
1
NiMH RE-PEAK
1
NiMH RE-PEAK
NiMH 1.3A 5.90V
RPC 005:33 00581
Note
CHG>DCHG 1
NiMH CYCLE
66
NiMH / NiCd Battery Program (cont.)
The “CHG>DCHG” option will  rst charge the battery
and then discharge the battery. If this screen does not
currently show the cycling option you desire, press the
START/ENTER button once and this setting will begin  ashing. Use the INC or DEC
buttons to change this setting.
Pressing the START/ENTER button again will cause the
number of cycles option to begin  ashing. Use the INC
or DEC buttons to change this to the number of cycles
you want the X4 AC Pro to run. The X4 AC Pro can cycle the battery a maximum of 5
times consecutively.
Program Start
Press and hold the START START/ENTER button until you see “BATTERY
CHECK...” the battery should then begin the cycle process.
Once cycling has commenced, the charger will display
the following real-time information: battery type,
charging/discharging current, battery voltage, charging
time and charged capacity. You will also see “D>C“ or “C>D“. This will indicate
which cycling order you have chosen. Either “D“ or “C“ will be  ashing. This  ashing
indicates which part of the cycle is currently being executed.
Once the cycling process is complete, the screen will read “END: CYCLE” and the
charger will emit a chiming sound. The X4 AC Pro will display the charge/discharge
capacity for each cycle. Using the INC. and DEC. buttons, you can scroll through this
data for each cycle.
CHG>DCHG 3
NiMH CYCLE
CHG>DCHG 1
NiMH CYCLE
NiMH 1.3A 5.90V
C>D 005:33 00581
66
NiMH Sensitivity
D.Peak 4mV/CELL
Ext. Temp ----
Int. Temp 37 C
Safety Time
ON 120min
In Power Voltage
12.6 V
Temp Cut-Off
ON 50 C
Capacity Cutoff
ON 500mAh
Additional Information Displayed During the Process
Pressing the INC or DEC buttons during the charging or discharging process al-
lows you to see a variety of other information on the screen.
Delta Peak voltage
sensitivity setting
External / Internal
temperatures
Safety timer setting
Temperature Cut-o
setting
Capacity Cut-o
setting
Input Voltage