User Manual

ManualsBrandsHitec RCD Inc. ManualsHobbyX4 AC Pro AC/DC 4 Port Multicharger

2120

3.81 3.82 3.81

0.00 0.00 0.00

Fuel = 66%

Cell = 3.98V

Lithium Battery Program (continued)

Program Stop

During the charging process, press STOP button to stop the process.

Program Complete

When the charging process is  nished, an audible

sound will be heard and the charger will indicate

END: FINSHED. The charger displays the total pack

voltage, total mAh fed into the battery and the

elapsed time of the process.

NOTE: The battery charge indicator displays Green during charging and Red

during discharging.

[ END: FINISH ]

12.60V 02001mAh

TIME: 00:32:15

12.60V 02001mAh

100

This screen shows the voltage of each individual cell

when a balancing cable is connected.

Charged capacity percentage and average cell voltage

of the pack.

Lithium Battery (LiPo, LiHV, LiFe, LiIon) Discharge Mode

The following steps will guide you through setting up a Lithium Chemistry Bat-

tery Discharge Mode.

DISCHARGING LITHIUM CHEMISTRY BATTERIES CAN CAUSE PERMANENT

DAMAGE TO THE BATTERY AND IT IS NOT RECOMMENDED FOR

ANYTHING OTHER THAN THE DISPOSAL OF THE BATTERY. IF YOU CHOOSE

TO DISCHARGE YOUR LITHIUM BATTERIES, MAKE SURE TO PAY CLOSE

ATTENTION TO THE MINIMUM VOLTAGE SETTING. IF YOU WANT TO STORE

YOUR BATTERY FOR A LONG PERIOD OF TIME YOU SHOULD UTILIZE THE

STORAGE MODE CHARGE PROGRAM AS THIS IS THE SAFEST METHOD OF

STORING YOUR LITHIUM CHEMISTRY BATTERIES.

BATT/PROGRAM Select

Press INC and DEC to cycle through all battery types

and press START/ENTER to select the appropriate

battery types to be charged.

Discharge Current

Press INC and DEC to adjust the discharge current.

Press the START/ENTER button to con rm the setting

of your choice. Adjustment range is 0.1 ~ 2.0 Amps.

Warning

2.0A 11.1V (3S)

LiPo DISCHARGE

2.0A 11.1V (3S)

LiPo DISCHARGE

Battery Cells

Press INC and DEC to scroll through the battery cells

supported by the charger. Press START/ENTER to select

the appropriate cells for your battery.

2.0A 11.1V (3S)

LiPo DISCHARGE

Lithium Battery Program (continued)

Now that you have set all the parameters for your battery you are ready to exe-

cute the operation. Now would be a good time to check to make sure the charge

settings are correct and within the battery manufacturers recommendations.

DURING CHARGING/DISCHARGING, THE BATTERY SHOULD BE PLACED

INSIDE A FIRE PROOF/RETARDANT BAG AND ON A FIRE PROOF SUR

FACE, AWAY FROM OTHER COMBUSTIBLE OBJECTS.

Program Start

Press and hold the START/ENTER button until you

see “BATTERY CHECK...” followed by the con rmation

screen. This screen displays the number of cells

you set up as “R” and the number of cells detected by

the processor as “S”. If both numbers are identical, you

may press the START button once to con rm and

begin charging. If these numbers do not match, press

the STOP button to return to the previous screen and

carefully check the number of cells before proceeding.

Caution

CONFIRM (ENTER)

R:3SER S:3SER

CANCEL (STOP)

R:3SER S:3SER

WAIT.....................

BATTERY CHECK

LP3s 3.2A 11.87V

BAL 010:01 00609

Discharge Status Monitor

Use the INC. and DEC. buttons to scroll through the various information dis-

played during the process.

This screen shows the type of battery, number of cells,

discharge current, total voltage of the pack, type of

process, elapsed time and number of mAh fed into the

battery.

3.81 3.82 3.81 0.00

0.00 0.00 0.00 0.00

Fuel = 66%

Cell = 3.98V

This screen shows the voltage of each individual cell

when a balancing cable is connected.

Discharged capacity percentage and average cell volt-

age of the pack.