Operation Manual
English
7
CHARGER
Model UC18YRSL UC18YGSL
Charging voltage 14.4 V – 18 V 14.4 V – 18 V
Weight 0.6 kg 0.4 kg
STANDARD ACCESSORIES
In addition to the main unit (1), the package contains the
accessories listed in the table below.
Standard accessories are subject to change without
notice.
8. Do not put or subject the battery to high
temperatures or high pressure such as into a
microwave oven, dryer, or high pressure container.
9. Keep away from fire immediately when leakage
or foul odor are detected.
10. Do not use in a location where strong static
electricity generates.
11. If there is battery leakage, foul odor, heat
generated, discolored or deformed, or in any way
appears abnormal during use, recharging or
storage, immediately remove it from the
equipment or battery charger, and stop use.
CAUTION
1. If liquid leaking from the battery gets into your
eyes, do not rub your eyes and wash them well
with fresh clean water such as tap water and
contact a doctor immediately.
If left untreated, the liquid may cause eye-
problems.
2. If liquid leaks onto your skin or clothes, wash well
with clean water such as tap water immediately.
There is a possibility that this can cause skin irritation.
3. If you find rust, foul odor, overheating, discolor,
deformation, and/or other irregularities when using
the battery for the first time, do not use and return
it to your supplier or vendor.
WARNING
If an electrically conductive foreign object enters the
terminals of the lithium ion battery, a short-circuit may
occur resulting in the risk of fire. Please observe the
following matters when storing the battery.
䡬 Do not place electrically conductive cuttings, nails,
steel wire, copper wire or other wire in the storage
case.
䡬 Either install the battery in the power tool or
store by securely pressing into the battery cover
until the ventilation holes are concealed to prevent
short-circuits (See Fig. 1).
SPECIFICATIONS
POWER TOOL
1
Charger (UC18YRSL or UC18YGSL) ...
1
WH18DSAL
2 Battery ............................................... 2
3 Plastic case ....................................... 1
4 Battery cover .................................... 1
1
Charger (UC18YRSL or UC18YGSL) ...
1
WH14DSAL
2 Battery ............................................... 2
3 Plastic case ....................................... 1
4 Battery cover .................................... 1
OPTIONAL ACCESSORIES
(Sold separately)
1. Battery
(BSL1430, (BSL1415X) (BSL1830, (BSL1815X)
BSL1440) BSL1840,
BSL1850)
Optional accessories are subject to change without notice.
APPLICATION
䡬 Driving and removing of machine screws, wood
screws, tapping screws, etc.
BATTERY REMOVAL/INSTALLATION
1. Battery removal
Hold the handle tightly and push the battery latch to
remove the battery (see Fig. 2).
CAUTION:
Never short-circuit the battery.
2. Battery installation
Insert the battery while observing its polarities (see
Fig. 2).
Model WH14DSAL WH18DSAL
No-load speed 0 – 2600 min
–1
Capacity (Ordinary bolt)
M6 – M14
Tightening torque
140 N·m 145 N·m
(Maximum)
Rechargeable battery
BSL1430: Li-ion BSL1440: Li-ion BSL1415X: Li-ion BSL1830: Li-ion BSL1840: Li-ion BSL1850: Li-ion BSL1815X: Li-ion
14.4 V (3.0 Ah 8 cells) 14.4 V (4.0 Ah 8 cells) 14.4 V (1.5 Ah 4
cells) 18 V (3.0 Ah 10 cells) 18 V (4.0 Ah 10 cells) 18 V (5.0 Ah 10 cells) 18 V (1.5 Ah 5 cells)
Weight 1.6 kg 1.6 kg 1.4 kg 1.7 kg 1.7 kg 1.7 kg 1.5 kg
01Eng_WH14DSAL_WE 6/14/13, 13:407