Instruction Manual
Table Of Contents
- 1 Safety summary
- 2 Switch Names and Functions
- 3 Operation
- 4 Icon Description
- 5 Function Menu
- 5.1 Simple Timer Setting
- 5.2 Operation Schedule Setting
- 5.3 Power Savings Setting
- 5.4 Night Quiet Operation
- 5.5 Power Saving/Night Quiet Schedule Setting
- 5.6 Power Consumption Display
- 5.7 Autoboost (QUICK MODE) Setting
- 5.8 Comfort Setting
- 5.9 Motion sensor setting
- 5.10 Setback Setting
- 5.11 Elevating Grille
- 5.12 Filter Reminder Reset Setting
- 5.13 FrostWash
- 5.14 Individual Louver Setting
- 5.15 Cancel Individual Louver Setting
- 5.16 Louver Open/Close
- 5.17 Ventilation
- 5.18 Total Heat Exchanger Setting
- 6 Service & installation menu
- 6.1 Installation menu
- 6.1.1 Test Run
- 6.1.2 Function selection
- 6.1.3 Thermistor Selection
- 6.1.4 Input / Output Setting
- 6.1.5 Thermistor Calibration in Controller
- 6.1.6 Fan Speed at Cooling Thermo-OFF
- 6.1.7 Fan Speed at Heating Thermo-OFF
- 6.1.8 Indoor Unit Address Change
- 6.1.9 Address Check Operation
- 6.1.10 Address Initialization
- 6.1.11 Setting Initialization
- 6.1.12 Main Remote Setting
- 6.1.13 Priority Setting
- 6.1.14 Cancel Preheating Control
- 6.1.15 Elevating grille Setting
- 6.1.16 Power Up Setting
- 6.1.17 Setback Trigger Unit
- 6.1.18 Refrigerant Leak Sensor Setting
- 6.2 Service menu
- 6.3 Check Menu
- 6.1 Installation menu
- 7 Screen Display Setting menu
- 8 Contact Information menu
- 9 Hotel Mode Setting
- 10 In Alarm Condition
Element Optional function
Individual
setting
Settings Setting conditions Description
S3 Not used -
00
- Use at 00 conditions
01
S4 Not used -
00
- Use at 00 conditions
01
S5 Not used -
00
- Use at 00 conditions
01
S6 Not used -
00
- Use at 00 conditions01
02
S7 Not used -
00
- Use at 00 conditions
01
02
03
04
05
06
07
S8 Not used -
00
- Use at 00 conditions
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
? NOTE
• O: allows for individual setting.
• X: the setting is made for all outdoor units.
• –: not used.
•
(1)
When J1 is set as activated function, the room temperature indication is the sensor value set at “C8”.
•
(2)
The Remote Control Switch shall be installed in a proper place for the correct detection of room temperature by its temperature sensor.
•
(3)
The Remote Sensor shall be installed in a proper place for the correct detection of room temperature.
•
(4)
In case that automatic louver is set, the louver will keep operating in both thermo-ON and thermo-OFF condition.
•
(5)
00 standard (7-step operation); 01 draft prevention (cannot be set to the lower two steps); 02 High ceilings (cannot be set the upper two steps).
•
(6)
In case that the set temperature is changed and kept within the set time at “F4”, the temperature is automatically changed to “F5” and “F6”. In
case that the set temperature is out of range at “F5” and “F6”, it is applied within upper and lower limit for the set temperature.
•
(7)
When the unit is restarted by the remote control switch, the temperature automatically changes to the setting temperature of “F5” or “F6”.
? NOTE
• On modifying the ”CF” (air outlet louver angle change) setting, restore the power supply or allow the automatic louver to make a full cycle in
automatic mode to apply the optional setting.
• The changes to the optional function settings must be done after 3 minutes have passed after startup.
• It is recommended to keep track of the changes made to optional function settings, for further reference.
• The optional settings are different according to the indoor and outdoor unit models. Check to ensure that the unit has the optional setting or not.
• The optional functions with “X” mark at the individual setting column can change the condition only when “All Rooms” is set.
• The following optional functions are disable when RPI Unit with Econofresh are installed: b7, bA, bd, bE, C1, C2, C3, C9, CA, Cd, CF, d6, E3, E5,
E7, E9, EA, FE, FF, H1, H3, H4, J2, J4, J7, J8, J9, JA, JB, K1, K2, K3, K4, K5.
EN
SERVICE & INSTALLATION MENU
PMML0565 rev.1 - 04/202257