Instruction Manual
Table Of Contents
- 1 Safety summary
- 2 Switch Names and Functions
- 3 Operation
- 4 Icon Description
- 5 Function Menu
- 5.1 Simple Timer Setting
- 5.2 Operation Schedule Setting
- 5.3 Power Savings Setting
- 5.4 Night Quiet Operation
- 5.5 Power Saving/Night Quiet Schedule Setting
- 5.6 Power Consumption Display
- 5.7 Autoboost (QUICK MODE) Setting
- 5.8 Comfort Setting
- 5.9 Motion sensor setting
- 5.10 Setback Setting
- 5.11 Elevating Grille
- 5.12 Filter Reminder Reset Setting
- 5.13 FrostWash
- 5.14 Individual Louver Setting
- 5.15 Cancel Individual Louver Setting
- 5.16 Louver Open/Close
- 5.17 Ventilation
- 5.18 Total Heat Exchanger Setting
- 6 Service & installation menu
- 6.1 Installation menu
- 6.1.1 Test Run
- 6.1.2 Function selection
- 6.1.3 Thermistor Selection
- 6.1.4 Input / Output Setting
- 6.1.5 Thermistor Calibration in Controller
- 6.1.6 Fan Speed at Cooling Thermo-OFF
- 6.1.7 Fan Speed at Heating Thermo-OFF
- 6.1.8 Indoor Unit Address Change
- 6.1.9 Address Check Operation
- 6.1.10 Address Initialization
- 6.1.11 Setting Initialization
- 6.1.12 Main Remote Setting
- 6.1.13 Priority Setting
- 6.1.14 Cancel Preheating Control
- 6.1.15 Elevating grille Setting
- 6.1.16 Power Up Setting
- 6.1.17 Setback Trigger Unit
- 6.1.18 Refrigerant Leak Sensor Setting
- 6.2 Service menu
- 6.3 Check Menu
- 6.1 Installation menu
- 7 Screen Display Setting menu
- 8 Contact Information menu
- 9 Hotel Mode Setting
- 10 In Alarm Condition
Element Optional function
Individual
setting
Settings Setting conditions Description
b9
Locking of fan speed setting
(Not available for models
KPI-E4)
X
00 Function disabled (factory setting)
This function prevents the
modication of the fan speed
of the unit from the remote
controller and from central
controls, once it has been
selected.
01 Function enabled
bA Not available X
“- -”
permanent
Not available –
bb
Cooling setting temperature
correction
O
00 No compensation (factory setting)
This function decreases the
setting temperature and is
used to produce longer cooling
periods.
01 Setting temperature decreased by 1°C
02 Setting temperature decreased by 2°C
bC Not used –
00
- Use at 00 conditions
01
bd Not used –
00
- Use at 00 conditions
01
bE Not used –
00
- Use at 00 conditions
01
C1 Not used –
00
- Use at 00 conditions
01
C2 Not available –
“- -”
permanent
- –
C3
Not used
–
00
- Use at 00 conditions
01
Only for DX-Interface,
KPI-E4E and KPI-X4E:
Fan stoppage delay
00 Function disabled (factory setting)
This function keeps the fan in
operation for 60 minutes after
stop of the KPI unit or DX-
Interface.
01 60 minutes
C4 Not used –
00
- Use at 00 conditions
01
C5
Static pressure selection
Models
RPI(L/H)-FSRE
RPI-FSN3(P)E(-f)
O
00 Standard static pressure (factory setting)
This function is used to change
the static pressure of the RPI
units from the remote control.
01 High static pressure
02 Low static pressure
Increase of fan speed during
normal operation (not during
heating Thermo-OFF)
Models
RCI-FSR
RCIM-FSRE
RCD-FSR
RPC-FSR
RPK-FSR(H)M
RPF(I)-FSN2E
O
00
Standard
(factory setting)
This function is used to change
the fan speed of indoor units
installed in high ceilings.
01 Hi Speed 1
02 Hi Speed 2
Fan speed setting on the remote controller
C5 High H High Medium Low
0 Hi2 Hi Me Lo
1 Hi2 Hi1 Hi Me
2 Hi2 Hi2 Hi1 Hi
(This function C5 is not available for DX-Interface models)
C6
Increase of fan speed at
heating Thermo-OFF
(Not available for models
KPI-E4 and KPI-X4E)
O
00
Function disabled
(factory setting)
This function is used to
increase the fan speed when
the thermostat reaches the
set temperature in heating
according to the setting of
function C5.
01 Function enabled
SERVICE & INSTALLATION MENU
PMML0565 rev.1 - 04/202242