Instruction Manual
Table Of Contents
- 1 Safety summary
- 2 Switch Names and Functions
- 3 Operation
- 4 Icon Description
- 5 Function Menu
- 5.1 Simple Timer Setting
- 5.2 Operation Schedule Setting
- 5.3 Power Savings Setting
- 5.4 Night Quiet Operation
- 5.5 Power Saving/Night Quiet Schedule Setting
- 5.6 Power Consumption Display
- 5.7 Autoboost (QUICK MODE) Setting
- 5.8 Comfort Setting
- 5.9 Motion sensor setting
- 5.10 Setback Setting
- 5.11 Elevating Grille
- 5.12 Filter Reminder Reset Setting
- 5.13 FrostWash
- 5.14 Individual Louver Setting
- 5.15 Cancel Individual Louver Setting
- 5.16 Louver Open/Close
- 5.17 Ventilation
- 5.18 Total Heat Exchanger Setting
- 6 Service & installation menu
- 6.1 Installation menu
- 6.1.1 Test Run
- 6.1.2 Function selection
- 6.1.3 Thermistor Selection
- 6.1.4 Input / Output Setting
- 6.1.5 Thermistor Calibration in Controller
- 6.1.6 Fan Speed at Cooling Thermo-OFF
- 6.1.7 Fan Speed at Heating Thermo-OFF
- 6.1.8 Indoor Unit Address Change
- 6.1.9 Address Check Operation
- 6.1.10 Address Initialization
- 6.1.11 Setting Initialization
- 6.1.12 Main Remote Setting
- 6.1.13 Priority Setting
- 6.1.14 Cancel Preheating Control
- 6.1.15 Elevating grille Setting
- 6.1.16 Power Up Setting
- 6.1.17 Setback Trigger Unit
- 6.1.18 Refrigerant Leak Sensor Setting
- 6.2 Service menu
- 6.3 Check Menu
- 6.1 Installation menu
- 7 Screen Display Setting menu
- 8 Contact Information menu
- 9 Hotel Mode Setting
- 10 In Alarm Condition
5.13.6 Display during FrostWash
If the indoor or outdoor temperature does not
meet the conditions for FrostWash, the following is
displayed.
If FrostWash is paused, the following is displayed.
- 1 When the indoor unit is out of the temperature
range
- 2 When the outdoor unit is out of the temperature
range
- 1 Press "OK" (Turn off the FrostWash)
- 2 FrostWash off screen
The above display will continue for about 8 minutes.
Please note that no operation can be done at that time.
If the room temperature is outside the range of 15°C
to 30°C, FrostWash will not be performed and the
pause screen is displayed. The display will disapper
when one of the remote controllers is operated after
the backlight is turned on.
If the room temperature is outside the range of 1°C
to 43°C, FrostWash will not be performed and the
pause screen is displayed. The display will disappear
when one of the remote controllers is operated after
the backlight is turned on.
The display of compeleted FrostWash will
disappear when one of the remote controllers is
operated after the backlight is turned on.
FrostWash in prepration
FrostWash in progess
Complete FrostWash
During FrostWash operation, the following screens
sequences are displayed:
? NOTE
• In each screen display, the backlight turns off after a
certain period of time (The default setting is 15 seconds.)
after operation, so it may be difcult to see the screen
display.
• If the display is difcult to see, press any switch to turn
on the backlight. At that time, if you press the "OK", the
screen will change to the
- 1 FrostWash pause screen.
EN
FUNCTION MENU
PMML0565 rev.1 - 04/202233