Instruction Manual
Table Of Contents
- 1 Safety summary
- 2 Switch Names and Functions
- 3 Operation
- 4 Icon Description
- 5 Function Menu
- 5.1 Simple Timer Setting
- 5.2 Operation Schedule Setting
- 5.3 Power Savings Setting
- 5.4 Night Quiet Operation
- 5.5 Power Saving/Night Quiet Schedule Setting
- 5.6 Power Consumption Display
- 5.7 Autoboost (QUICK MODE) Setting
- 5.8 Comfort Setting
- 5.9 Motion sensor setting
- 5.10 Setback Setting
- 5.11 Elevating Grille
- 5.12 Filter Reminder Reset Setting
- 5.13 FrostWash
- 5.14 Individual Louver Setting
- 5.15 Cancel Individual Louver Setting
- 5.16 Louver Open/Close
- 5.17 Ventilation
- 5.18 Total Heat Exchanger Setting
- 6 Service & installation menu
- 6.1 Installation menu
- 6.1.1 Test Run
- 6.1.2 Function selection
- 6.1.3 Thermistor Selection
- 6.1.4 Input / Output Setting
- 6.1.5 Thermistor Calibration in Controller
- 6.1.6 Fan Speed at Cooling Thermo-OFF
- 6.1.7 Fan Speed at Heating Thermo-OFF
- 6.1.8 Indoor Unit Address Change
- 6.1.9 Address Check Operation
- 6.1.10 Address Initialization
- 6.1.11 Setting Initialization
- 6.1.12 Main Remote Setting
- 6.1.13 Priority Setting
- 6.1.14 Cancel Preheating Control
- 6.1.15 Elevating grille Setting
- 6.1.16 Power Up Setting
- 6.1.17 Setback Trigger Unit
- 6.1.18 Refrigerant Leak Sensor Setting
- 6.2 Service menu
- 6.3 Check Menu
- 6.1 Installation menu
- 7 Screen Display Setting menu
- 8 Contact Information menu
- 9 Hotel Mode Setting
- 10 In Alarm Condition
4 ICON DESCRIPTION
The status of the remote controller is displayed on the operation screen.
? NOTE
• It may not be displayed depending on the type of outdoor unit or indoor unit you are using.
• If there are multiple status, the high priority icon is displayed rst.
No. Icon Description
1 A schedule timer is set.
2
Set the current time. Schedule timer operation is not possible.
3
The off timer is set.
4
The operation lock is set.
5 Displayed when using the central controller. Remote control operation is restricted.
6
It is time to freeze-clean the heat exchanger.
7
It is time to clean the air lter.
8 A/C Air-conditioning operation is performed.
9
Ventilation
Total heat ventilation
Automatic ventilation
Normal ventilation
Ventilation, automatic ventilation, total heat ventilation, and normal ventilation are operating.
10
** ºC
Displays the room temperature. (*1)
11 SAG Elevating grille is not stored correctly.
12 Emergency operation Emergency operation is in progress.
13 Setback When setback operation is enabled and the card key is removed (when no one is present). (*2)
14 Purging In night purge progress.
15 Setback aborted Setback is aborted.
16 Motion sensor ON Indicates capacity savings by motion sensor control during operation or stop.
17 Radiant sensor
In order to efciently heat the room when the radiant temperature is low, the air ow direction and
speed are automatically controlled.
18 Cold draft restrained To prevent a too low air outlet temperature from indoor unit.
19 Noise reduction The operation noise reduction control of the outdoor unit is set.
20 FrostWash is complete Indicates the FrostWash is performed.
21
Indoor unit temperature over range,
FrostWash stopped
If the indoor temperature is out of the range of 15°C to 30°C, no FrostWash is performed and the
cancellation is displayed.
22
Outdoor unit temperature over
range, FrostWash stopped
If the outdoor temperature is out of the range of 1°C to 43°C, no FrostWash is performed and the
cancellation is displayed.
EN
ICON DESCRIPTION
PMML0565 rev.1 - 04/20227