Liquid Crystal Projector ED-S3170A / ED-X3270A USER'S MANUAL, Vol. 1 Please read this user's manual thoroughly to ensure correct usage through understanding. TECHNICAL REGULATORY NOTICES ENGLISH 00CP-X380W 01.11.
01ED-S317-27/Vol1/E/初 02.12.17 8:57 AM ページ 1 LCD Projector ED-S3170A/ED-X3270A USER'S MANUAL Vol.1 (Basic) ENGLISH Thank you for purchasing this projector. WARNING • Please read the accompanying manual “SAFETY INSTRUCTIONS” and this “USER'S MANUAL” thoroughly to ensure correct usage through understanding. After reading, store this instruction manual in a safe place for future reference. NOTE • The information in this manual is subject to change without notice.
01ED-S317-27/Vol1/E/初 02.12.17 8:57 AM ページ 2 PROJECTOR FEATURES This liquid crystal projector is used to project various computer signals as well as NTSC / PAL / SECAM video signals onto a screen. Little space is required for installation and large images can easily be realized.
01ED-S317-27/Vol1/E/初 02.12.17 8:57 AM ページ 3 1 Connect your devices to the projector 2 Insert the batteries into the remote control 3 Connect the power cord Connect your computer, VCR and/or other devices you will be using to the projector. 8 ENGLISH WARNING Precautions to observe in regards to the power cord: Please use extra caution when connecting the projector's power cord as incorrect or faulty connections may result in FIRE AND/OR ELECTRICAL SHOCK.
01ED-S317-27/Vol1/E/初 02.12.
01ED-S317-27/Vol1/E/初 02.12.
01ED-S317-27/Vol1/E/初 02.12.17 8:57 AM ページ 6 SETTING UP THE PROJECTOR CAUTION • Install the projector in a suitable environment according to instructions of the accompanying manual “SAFETY INSTRUCTIONS” and this manual. • If you press the elevator buttons without holding the projector, the projector might crash down, overturn, smash your fingers and possibly result in malfunction.
01ED-S317-27/Vol1/E/初 02.12.17 8:57 AM ページ 7 Adjusting the Screen Size and Projection Distance Refer to the illustrations and tables below to determine the screen size and projection distance. The screen Top view ENGLISH The values shown in the table are calculated for a full size screen (ED-S3170A: 800x600 pixels/ED-X3270A: 1024x768 pixels).
01ED-S317-27/Vol1/E/初 02.12.17 8:57 AM ページ 8 CONNECTING YOUR DEVICES Devices You Can Connect to the Projector (Refer to this section for planning your device configuration to use for your presentation.) CAUTION • Incorrect connecting could result in fire or electrical shock. Please read this manual and the separate “SAFETY INSTRUCTIONS”.
01ED-S317-27/Vol1/E/初 02.12.17 8:57 AM ページ 9 Ports and Cables Function Projector Port RGB IN 1 RGB input RGB IN 2 RGB output RGB OUT USB mouse control USB ENGLISH Refer to the table below to find out which projector port and cable to use for connecting a given device. Use this table for determining which cables to prepare.
01ED-S317-27/Vol1/E/初 02.12.17 8:57 AM ページ 10 CONNECTING YOUR DEVICES (continued) Connecting to a Computer ATTENTION Whenever attempting to connect a laptop computer to the projector, be sure to activate the laptop's RGB external image output (set the laptop to CRT display or to simultaneous LCD and CRT display). For details on how this is done, please refer to the instruction manual of the corresponding laptop computer.
01ED-S317-27/Vol1/E/初 02.12.
01ED-S317-27/Vol1/E/初 02.12.
01ED-S317-27/Vol1/E/初 02.12.17 8:57 AM ページ 13 USING THE REMOTE CONTROL CAUTION Precautions to observe in regards to the batteries Always handle the batteries with care and use them only as directed. Improper use may result in battery cracking or leakage, which could result in fire, injury and/or pollution of the surrounding environment. • Keep the battery away from children and pets. • Be sure to use only the batteries specified for use with the remote control. Do not mix new batteries with used ones.
01ED-S317-27/Vol1/E/初 02.12.17 8:57 AM ページ 14 TURNING ON THE POWER Precautions Connect all devices to be used to the projector prior to turning on the power. 8 ∼ 12 WARNING When the power is ON, a strong light is emitted. Do not look into the lens.
01ED-S317-27/Vol1/E/初 02.12.17 8:57 AM ページ 15 5 Using the remote control If selecting RGB input Press the RGB button Using the projector's control panel Press the INPUT button Press this button to toggle between the devices connected to RGB IN 1 and 2. As illustrated below, each time you press the RGB button, the projector switches between RGB IN 1 and 2. Select the signal you wish to project.
01ED-S317-27/Vol1/E/初 02.12.17 8:57 AM ページ 16 TURNING OFF THE POWER 1 The message "Power off?" will appear on the screen for approximately 5 seconds. STANDBY/ON VIDEO RGB ASPECT MAGNIFY Press the STANDBY/ON button (control panel or remote control) STANDBY/ON SEARCH AUTO BLANK HOME PAGE UP VOLUME END PAGE DOWN MUTE ON OFF FREEZE 2 KEYSTONE POSITION Press the STANDBY/ON button again while the "Power off?" message is visible. The projector lamp goes off and starts cooling down.
01ED-S317-27/Vol1/E/初 02.12.17 8:57 AM ページ 17 ADJUSTING THE VOLUME STANDBY/ON VIDEO RGB ASPECT SEARCH AUTO BLANK HOME PAGE UP VOLUME END PAGE DOWN MUTE Press the VOLUME button VOLUME ENGLISH 1 As illustrated on the right, a dialog will appear on the screen to aid you in adjusting the volume. VOLUME MAGNIFY ON 16 OFF FREEZE KEYSTONE 2 POSITION MENU , buttons to adjust Press the VOLUME button again to close the dialog and complete this operation.
01ED-S317-27/Vol1/E/初 02.12.17 8:57 AM ページ 18 ADJUSTING THE POSITION 1 STANDBY/ON VIDEO RGB ASPECT MAGNIFY SEARCH AUTO BLANK HOME PAGE UP VOLUME END PAGE DOWN MUTE Press the POSITION button As illustrated on the right, a dialog will appear on the screen to aid you in adjusting the position.
01ED-S317-27/Vol1/E/初 02.12.17 8:57 AM ページ 19 USING THE AUTOMATIC ADJUSTMENT FEATURE Press the AUTO button AUTO STANDBY/ON VIDEO RGB ASPECT MAGNIFY SEARCH AUTO BLANK HOME PAGE UP VOLUME END PAGE DOWN MUTE Automatic Adjustment for RGB Input ENGLISH 1 ON OFF FREEZE KEYSTONE POSITION MENU ENTER ESC Horizontal position (H. POSIT), vertical position (V. POSIT), clock phase (H. PHASE) and horizontal size (H. SIZE) are automatically adjusted.
01ED-S317-27/Vol1/E/初 02.12.17 8:57 AM ページ 20 CORRECTING KEYSTONE DISTORTIONS 1 STANDBY/ON VIDEO RGB ASPECT SEARCH AUTO BLANK HOME PAGE UP VOLUME END PAGE DOWN Press the KEYSTONE button As illustrated on the right, a dialog will appear on the screen to aid you in correcting the distortion.
01ED-S317-27/Vol1/E/初 02.12.17 8:57 AM ページ 21 USING THE MAGNIFY FEATURE Press the MAGNIFY (ON) button The projector enters MAGNIFY mode.
01ED-S317-27/Vol1/E/初 02.12.17 8:57 AM ページ 22 SIGNAL SEARCHING 1 STANDBY/ON VIDEO RGB ASPECT MAGNIFY SEARCH AUTO BLANK HOME PAGE UP VOLUME END PAGE DOWN MUTE ON Press the SEARCH button When you press the SEARCH button, the projector begins searching for input signals. If it detects an input signal, the search will cease and the projector will project the detected signal.
01ED-S317-27/Vol1/E/初 02.12.17 8:57 AM ページ 23 USING THE MENU FUNCTIONS 1 Press the MENU button 2 / Select a menu using the buttons, then press the or ENTER button. RGB ASPECT MAGNIFY SEARCH AUTO BLANK HOME PAGE UP VOLUME END PAGE DOWN ON MUTE The menu display appears on the screen. The projector has the following menus: MAIN, PICTURE-1, PICTURE-2, INPUT, SCREEN, and OPTION. Select a menu using the / buttons.
01ED-S317-27/Vol1/E/初 02.12.17 8:57 AM ページ 24 OPERATING THE PC SCREEN You can use the remote control as a simplified mouse or keyboard. CAUTION Caution: Mistaken use of the mouse/keyboard control could damage your equipment. • Only connect to a PC. • Before connecting, read the manuals of the device you will connect. • Do not unplug the connector cables while the computer is operating.
01ED-S317-27/Vol1/E/初 02.12.17 8:57 AM ページ 25 HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE Before replacing the lamp, check the serial number of the replacement lamp bulb (sold separately: DT00511 for ED-S3170A/DT00521 for ED-X3270A), then contact your local dealer. Before replacing the lamp, turn off the power, and unplug the power cord, then wait at least 45 minutes, in order to ensure that the lamp is properly cooled.
01ED-S317-27/Vol1/E/初 02.12.17 8:57 AM ページ 26 THE LAMP (continued) Replacing the lamp All projector lamps will wear out eventually. If used for long periods of time, the image could become darkened, and the color contrast could be impacted as well. We recommend that you replace your lamps early. If the LAMP indicator turns red, or a message prompts you to replace the lamp when you power up the projector, the lamp needs to be replaced. (See "Related Messages" (Vol.
01ED-S317-27/Vol1/E/初 02.12.17 8:57 AM ページ 27 THE AIR FILTER The air filter should be cleaned about every 100 hours. If the LAMP indicator and TEMP indicator blink red simultaneously, or a message prompts you to clean the air filter when you turn on the unit, the filter needs to be cleaned. (See "Related Messages" (Vol.2 7 ) and "Regarding the Indicator Lamps" (Vol.2 8 ) for details.
01ED-S317-27/Vol1/E/初 02.12.17 8:57 AM ページ 28 THE AIR FILTER (continued) Replacing the air filter If the soiling will not come off the air filter, or it becomes damaged, then it needs to be replaced. Please contact your local dealer, after confirming the model of your separately sold replacement air filter. (See "Optional Parts" on Vol.2 10 .) 1 Turn off the projector, and unplug the power cord.
01ED-S317-27/Vol1/E/初 02.12.17 8:57 AM ページ 29 OTHER CARE In order to ensure the safe use of your projector, please have it cleaned and inspected by your local dealer about once every 2 years. Never try to care for the inside of the unit yourself. Doing so is dangerous. ENGLISH Caring for the inside of the projector : Caring for the lens : Lightly wipe the lens with a commercially available lens-cleaning wipe. Do not touch the lens directly with your hand.
ED-S3170/X3270/Vol.2/ENG 02.12.17 10:15 AM ページ 1 USER'S MANUAL ENGLISH LCD Projector ED-S3170A/ED-X3270A Vol.2 (Extended) Thank you for purchasing this projector. WARNING • Please read the accompanying manual “SAFETY INSTRUCTIONS” and this “USER'S MANUAL” thoroughly to ensure correct usage through understanding. After reading, store this instruction manual in a safe place for future reference. NOTE • The information in this manual is subject to change without notice.
ED-S3170/X3270/Vol.2/ENG 02.12.17 10:15 AM ページ 2 MULTIFUNCTIONAL SETTINGS This device has 6 separate menus: MAIN, PICTURE 1, PICTURE 2, INPUT, SCREEN, OPTION. Each of these menus is operated using the same methods. The basic operations of these menus are as follows. Menu screen display : Press the "MENU" button. Menu selection : Choose a menu name using the / button, and press the button or the ENTER button. Item selection : Choose an item using the / button, and press the button or the ENTER button.
ED-S3170/X3270/Vol.2/ENG 02.12.17 10:15 AM ページ 3 With the PICTURE 1 menu, the five items shown in the Table below can be performed. Perform each operation in accordance with the instructions in the Table.
ED-S3170/X3270/Vol.2/ENG 02.12.17 10:15 AM ページ 4 MULTIFUNCTIONAL SETTINGS (continued) INPUT Menu With the INPUT menu, the four items shown in the Table below can be performed. With inputting of RGB IN 1 and RGB IN 2 signals, the horizontal and vertical frequencies of the signals will be displayed on the initial screen of the INPUT menu. Perform each operation in accordance with the instructions in the Table.
ED-S3170/X3270/Vol.2/ENG 02.12.17 10:15 AM ページ 5 With the SCREEN menu, the five items shown in the Table below can be performed. Please perform each operation in accordance with the instructions in the Table. MENU MAIN PICTURE-1 PICTURE-2 INPUT SCREEN OPTION BLANK START UP MyScreen MyScreen Size MyScreen Lock MyScreen ORIGNAL ENGLISH SCREEN Menu : SELECT Example : SCREEN Menu (BLANK) SCREEN Menu Item Description BLANK Selection of BLANK Screen: MyScreen ⇔ ORIGINAL ⇔ . . ⇔ . . ⇔ . .
ED-S3170/X3270/Vol.2/ENG 02.12.17 10:15 AM ページ 6 MULTIFUNCTIONAL SETTINGS (continued) OPTION Menu With the OPTION menu, the five items shown in the Table below can be performed. Please perform each operation in accordance with the instructions in the Table.
ED-S3170/X3270/Vol.2/ENG 02.12.17 10:15 AM ページ 7 ENGLISH WHAT TO DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED Related Messages When the unit's power is ON, messages such as those shown below may be displayed. When any such message is displayed on the screen, please respond as described below. Message CHANGE THE LAMP AFTER REPLACING LAMP, RESET THE LAMP TIMER. (Note 1) Description Lamp usage time is approaching 2,000 hours. (Note 2) Preparation of a new lamp, and an early lamp change, is recommended.
ED-S3170/X3270/Vol.2/ENG 02.12.17 10:15 AM ページ 8 Regarding the Indicator Lamps Lighting and flashing of the POWER indicator, the LAMP indicator, and the TEMP indicator have the meanings as described in the Table below. Please respond in accordance with the instructions within the Table.
ED-S3170/X3270/Vol.2/ENG 02.12.17 10:15 AM ページ 9 ENGLISH WHAT TO DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED (continued) Phenomena That May Easily Be Mistaken for Machine Defects Before requesting repair, check in accordance with the following chart. If the situation cannot be corrected, then contact your dealer.
ED-S3170/X3270/Vol.2/ENG 02.12.17 10:15 AM ページ 10 SPECIFICATIONS NOTE • This specifications are subject to change without notice. Item Product name Liquid crystal panel Specification Liquid crystal projector Panel size 1.8 cm (0.7 type) Drive system TFT active matrix Pixels ED-S3170A：480,000 pixels (800 horizontal x600 vertical) ED-X3270A：786,432 pixels (1024 horizontal x 768 vertical) Lens Zoom lens F=1.7 ~ 1.9 f=21.7 ~ 26.1 mm Lamp 150 W UHB Speaker 1.0W Power supply AC100 ~ 120V, 2.
WARRANTY AND AFTER-SERVICE If a problem occurs with the equipment, first refer to the 7 “WHAT TO DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED” section and run through the suggested checks. If this does not resolve the problem contact your dealer or service company. They will tell you what warranty condition is applied. ENGLISH ED-S3170/X3270/Vol.2/ENG 02.12.
ED-S3170/X3270/TECHNICAl 02.12.17 9:25 AM ページ 1 TECHNICAL SIGNAL CONNECTOR PIN ASSIGNMENT RGB IN [1]/[2] RGB OUT S-VIDEO D-sub 15-pin Shrink Pin No Signal Mini Din 4-pin Pin No Signal 1 Video input Red 9 - 2 3 4 5 6 7 8 Video input Green Video input Blue Ground Ground Red Ground Green Ground Blue 10 11 12 13 14 15 Ground RGB IN [1]: SDA (DDC) RGB IN [2]: RGB OUT : H. sync./ Composite sync.
ED-S3170/X3270/TECHNICAl 02.12.17 9:25 AM ページ 2 EXAMPLE OF COMPUTER SIGNAL Display mode Resolution H×V fH (kHz) fV (Hz) Rating Signal mode ED-S3170A ED-X3270A 720 × 400 37.9 85.0 VESA TEXT Zoom in Zoom in 640 × 480 31.5 59.9 VESA VGA (60Hz) Zoom in Zoom in 640 × 480 35.0 66.7 Mac13"mode Zoom in Zoom in 640 × 480 37.9 72.8 VESA VGA (72Hz) Zoom in Zoom in 640 × 480 37.5 75.0 VESA VGA (75Hz) Zoom in Zoom in 640 × 480 43.3 85.
ED-S3170/X3270/TECHNICAl 02.12.17 9:25 AM ページ 3 INITIAL SET SIGNALS The following signals are used for the initial settings. The signal timing of some computer models may be different. In such case, refer to adjust the V.POSIT and H.POSIT of the menu. Back porch b Front porch d Display interval c Back porch b Front porch d Display interval c DATA DATA HSYNC VSYNC Sync a Horizontal signal timing (µs) TEXT a 2.0 b 3.0 c 20.3 d 1.
ED-S3170/X3270/TECHNICAl 02.12.
ED-S3170/X3270/TECHNICAl 02.12.17 9:25 AM ページ 5 RS-232C COMMUNICATION (1) Turn off the projector and computer power supplies and connect with the RS-232C cable. (2) Turn on the computer power supply and after the computer has started up, turn on the projector power supply.
ED-S3170/X3270/TECHNICAl 02.12.17 9:25 AM ページ 6 RS-232C COMMUNICATION (continued) Requesting projector status (Get command) (1) Send the request code Header + Command data (‘02H’+‘00H’+ type (2 bytes) +‘00H’+‘00H’) from the computer to the projector. (2) The projector returns the response code ‘1DH’+ data (2 bytes) to the computer.
ED-S3170/X3270/TECHNICAl 02.12.
ED-S3170/X3270/TECHNICAl 02.12.17 9:25 AM ページ 8 Command data chart (continued) Names Operation type H.Position Reset Execute BE EF 03 H.
ED-S3170/X3270/TECHNICAl 02.12.
ED-S3170/X3270/TECHNICAl 02.12.
REGULATORY NOTICES 02.12.17 9:11 AM ページ 1 REGULATORY NOTICES FCC Statement Warning WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
00ED-S317-27WBasic/初 02.12.17 9:11 AM ページ 1 Hitachi America, Ltd. Hitachi France Computer Division 2000 Sierra Point Parkway, MS760 Brisbane, CA 94005-1835 Tel: +1-800-225-1741 Fax: +1-650-244-7776 www.hitachi.com/lcd. Immeuble, 'Ariane', 18 Rue Grange Dame Rose, B.P. 134, 78148 Velizy, Cedex, France Tel: +33-1-34630542 Fax: +33-1-34650761 Hitachi Canada, Ltd.
