HITACHI / Liquid Crystal Projector Model CP-X960W/E USER'S GUIDE Thank you for purchasing the Hitachi liquid thoroughly to ensure correct usage through manual in a safe place for future reference. crystal understanding. Outline projector computer is used to project signals as well as NTSC/PAL/SECAM video signals onto a screen. Little space is required for installation and large images can easily be realized.
Before Use About the Symbols Various symbols are used in this instruction ensure correct usage, to prevent property damage. The meanings important contents. manual and on the product danger to the user of these symbols that you read these descriptions and others, and to prevent are described below.
[Safety Precaution] • If a problem should occur. • Do not insert ® If smoke or a strange odor arise, continued use could result in fire or electrical shock. In such case, immediately turn off the power switch and then disconnect the power plug from the power outlet. After making sure that power power if there is no image or sound, or if the sound is distorted. Continued use could result in fire or electrical Disconnect the plug from the power outlet. shock.
• Handle the power cord with care. ®Do not damage, cut, process • High or strongly twist the power cord. Placing heavy objects on the power cord, heating or strongly pulling the power cord can result damage as welt as fire or electrical shock. • Pulling on the power cord temperatures are generated when the lamp is lit, so do not place objects front of the lens. _.
• Do this not sit or place heavy objects • projector. where children are present. Do not place heavy objects _"_ Do not block the ventilation or falling openings. Care and purposes, plug from the before starting maintenance the terminals the in a humid near a humidifier the or other locations • Use the caster brakes. When installing this projector on a stand moving with overturning personal Do not handle plus and aligned due to battery A and injury.
• When the projector for an extended • is not to be used For safety purposes when the projector is not to be used for an / the projector. ® When moving the projector, be sure to close the lens cover, disconnect period. extended period because of travel, etc., always disconnect the power Moving _1_ the power plug from the power outlet and disconnect all external Disconnect plug plug from the power outlet. Also power outlet. close the lens cover to prevent the lens connections.
Checking the package Contents Make sure all of the following items are included in the package. If anything is missing, please contact your dealer. Projector unit Remote control Remote control Batteries User's Guide (this document) CP-X960W CP_XO60E 110V-US Power Cord 220*UK, Europe ( video/Audio cable ) 3_Conductor 220.
Names and functions of each part (continued) / Remote control photoreceptor Main power switch Used to turn the power on and off, © : OFF I:ON AC IN jack / Used to connect the accessory power cord. I/_Cautionl Connecting Make sure the accesory VIDEO to the AC IN jack power cord is plugged into the AC IN jack as far as it will go. Incomplete connection can result in fire or electrical shock.
Names and functions of each part (continued) Remote control transmitter Press to switch the input. (Refer to page 13, 19.) VIDEO, RGB button _ STANDBY / ON button _ _ VEOEO Turns the laser beam on and off. Refer to page LASER button 11 cocnerning usage and observe the cautions. sTAN_B¥/oN_ PosmoN Used to turn the power on and off. Press for 1 sec. or more to turn the power off (enter standby status). (Refer to pages13 and 14.
Names and functions of each part (continued) fLoading the batteries []Remove the cover. Push the lifting cover. up Loading AA batteries battery into the remote control. oadng heba eres Make sure the plus and knob the while minus poles are correctly oriented. battery []Close [/t_Caution] ®Use only Battery usage cautions the specified batteries with this projector. Also, do not mix new and old batteries. This could cause in battery cracking or leakage, injury.
Installation Typical LCD Projector and Screen Installation Use the diagram below as reference to determine -" To_D view Screen ) the screen size and projection distnace. S _) Side view \_ _h ) ) / a (inches) Screen size (inches) b (inches) Minimum Maximum 4O 55 73 1 6O 85 114 2 8O 114 151 2 100 144 191 3 120 176 231 3 a. Distance b.Distance from the LCD projector to the screen from the lens center to the bottom of the screen (a,b : +/-10%).
Basic operations To project 1 m 5 7 4 2 5_ j4 1 _ 1 Turn on the main power switch of the projector [ I: ON]. • The Power indicator 2 lights orange. Press the STANDBY / ON button. • The Power indicator will blink green and then light green. • The green blinking indicates warmup. • After the power is turned on, the lamp will be cooled for approximately be turned on even by pressing the STANDBYJON button. 1 rain. and the power cannot 3 Remove 4 Use the ZOOM button to adjust the screen size.
Basic operations (continued) Turning off the power] 1 2 P _n P MUTE BLANK 1 Press the STANDBY/ON • The Power indicator button for approximately wilt blink orange, then the lamp wilt turn off. Approximately lamp will light orange. • After the power is turned off, the lamp will be cooled for approximately AUTO TIMER 1 sec. 1 sec. after that, the 1 min. and the power cannot be turned off even by pressing the STANDBY/ON button.
Basic operations (continued) / [Freeze function] This function is used to freeze the image being displayed. (refer to page 10) p _nP MUTE C) @ BkANK AUTO TIMER C)(2)C) 1 Press the FREEZE button. • The image being displayed • The [ || ] mark appears will freeze. in the lower fight corner of the screen when the Freeze function Cancelling the FREEZE function 1 is on. I Press the FREEZE button. • The FREEZE function will be cancelled.
Basic operations (continued) I Magnify function Part of an image can be displayed (refer to page 10) m4 magnified. S_ 5 j6 p _n p BL_NK 1 MUTE AUTO TIMER Press the MAGNIFY + button. • The center part of the image wilt be displayed magnified Changing the magnification approximately two times. ratio ] Press the MAGNIFY + button. • When this button is pressed, the image wilt be displayed 3 Press the MAGNIFY- even larger. button.
Adjustments and functions 1,2,3 \3 1 1 Press the MENU ( _)_)(_(_ ) buttons of the projector or the MENU button of the remote control. • The Menu screen wilt appear. (refer to page 18 - 21 for details.) 2 Press the MENU ((i)_)_)(_)) buttons of the projector or the DISK PAD button of the remote control to select the menu item to be adjusted. 3 • The selected menu item will be displayed in orange.
Adjustments and functions (continued) SET UP Images and display positions can be adjusted from the SETUP menu.
Adjustments and functions (continued) / INPUT 1 The INPUT menu is used to select RGB signal sync signal frequency of the monitor VIDEO • _ J RGB VIDEO _. fH:38kHz fV:60Hz Adjustment signal. tMAG E IMAG E RGB and the VIDEO item Adjustment t, AUTO NTSC PAL SECAM NTSC4 43 M_PAL N-PAL description RGB Displays the following RGB inputs fH: horizontal sync frequency fV: vertical sync frequency VIDEO Sets the video signal system.
Adjustments and functions (continued) IMAGE Projection image inversion, etc., can be selected from the IMAGE SETUP INPUT IMAGE menu.
Adjustments and functions (continued) / OPT Communication functions, etc., can be set from the OPT menu. OM BITS TIMER [SETUP[ _NPUT COMSPEED COMBITS TIMER LANGUAGE AUTO OFF SYNC ON G • LANGUAGE COMSPEED SYNC ON G SETUP INPUT IMAGE bOR_ • [ S E T U P ] IN P U T [ [ M A G E COMSPEED C_COM_TS _MER _TIMER LANGUAGE Adjustment item COM. SPEED COM. BITS TIMER Adjustment Sets the communication description speed (5 steps). Sets the bit configuration for the communication 7N1...
Connection to the video signal terminals 1. Input signals Brightness signal Color signal S-VIDEO signal 1.0V p-p, 75 £2terminator 0.286V p-p (burst signal), 75 £2 terminator 1.0V p-p, 75 £2terminator VIDEO signal Input 200mV rms, 20k £2or less (max. 3.0V p-p) Output 0-200mVrms, Audio signal 1k 2. Signal input jacks Brightness signal Color signal Ground Ground S-VIDEO input (mini DIN 4-pin) _Caution_ The priority sequence of the video input jacks is as follows.
Connectiontothe RGBsignalterminal(continued) 3. Example of computer signal Resolution Hx V fH (kHz) fV (Hz) 640 x 400 24.8 56,4 640 x 350 37.9 85,1 640 x 400 37.9 720 x 400 Rating Signal mode Display mode NEC PC9800 Zoom in VESA VGA-1 Zoom in 85.1 VESA VGA-2 Zoom in 37.9 85.0 VESA TEXT Zoom in 640 x 480 31,5 59.9 VESA VGA-3 Zoom in 640 x 480 35,0 66.7 Mac13"mode Zoom in 640 x 480 37,9 72.8 VESA VGA-3(72Hz) Zoom in 640 x 480 37,5 75.
Connectiontothe RGBsignalterminal(continued) 4. Initial set signals The following signals are used for the initial settings. The signal timing of some computer models may be different. the V_POS1T and H.POS1T of the menu. In such case, refer to pages 17 and 18 and adjust Back porch b :_'-! DATA _ ,I ! HSYNC _C_ Computer/Signal Front porch d i Display interval c 1i 1i Synca Horizontal signal timing (ps) Computer/Signal a b c d VGA-1(85Hz) 2.0 3.0 20.3 1.0 SVGA (72Hz) VGA-2(85Hz) 2.
Connecting the USB 1. Connect the projector and computer with a suitable commercially 2. Press the 1NPUT button of the projector where the computer is to be connected. 3. Start the mouse function. or the RGB available 1/2 button cable. of the remote control / and select the input 4. Refer to page 10, 26 concerning the remote control of mouse operations. 5. Varying the force with which the DISK PAD button is pressed varies the speed of mouse operation.
Connection to the control signal terminal 1. Mouse functions (1) Turn off the main power switches provided projector. or an optional suitable of the projector commercially and computer available and connect cable. the two units with the cable Disconnect the USB cable (2) Turn on the main switch of the projector (the ON indicator lamp will light green).
Connection tothecontrolsignalterminal(continued) CONTROL signal jack RS-232C PS/2 ADB Serial 1 BUS CLK 3 DATA 5 XB SELO SELO 7 RTS RTS SELO RTS RTS ( YA +5V_ GND_ RTS GND +5V +5V GND GND +5V GND GND 11 SW-L 12 SEL-1 13 RD 14 TD II DATA ( SELO 8 9 Mouse jack Mini DIN 4-pin (POWER ON) ADB XA 6 Computer DATA 4 10 Projector YB 2 | ADB (Mac) mouse Mouse Pin no.
Connection tothecontrolsignalterminal(continued) 2. RS232C communication (1) Turn off the projector and computer power supplies and connect with the RS232C cable. (2) Turn on the computer power supply and, after the computer has started up, mm on the projector power supply. (3) Refer to page 20, 21 and set the communication speed and the number of communication bits. (4) Start RS232C communication.
Connection tothecontrolsignalterminal(continued) Command data chart Item 00h=disable COMMUNICATE 0Xh=8N1, mouse function, 01 - 7Fh=start mouse function 1Xh=7N1 X0h=1200bps, X1h=2400bps, X2h=4800bps, X3h=9600bps, X4h=19200bps POWER 3Eh=power ZOOM 01 - 3Fh=Zoom +, 41 - 7Fh=Zoom - FOCUS 01 - 3Fh=Focus +, 41 - 7Fh=Focus - MIRROR 00h=Normal, 01h=H : Invert, 02h=V : Invert, 03h=H & V : Invert INPUT 1lh=VIDEO, 21h=RGB1, 22h=RGB2 SYSTEM(VIDEO) 00h 00h off (standby status), 3Fh=power on 00h
Connection tothecontrolsignalterminal(continued) Requesting projector status (1) Send the request code '20H' + 'yyH' (2) The projector returns the response Changing the projector settings (1) Send the setting code '3xH' + 'yyH' (2) The projector (3) The projector from the computer code ' 1xH' + 'yyH' to the projector. +data to the computer. +data from the computer to the projector. changes the setting based on the above setting code. returns the response code ' 1xH' + 'yyH' +data to the computer.
Example of system setup Computer (notebook type) / AC input @ / I \ i i Computer (desktop type) i i Video tape recorder with S jack i i Video tape recorder Speaker (with built-in amp) ( Caution Display monitor Turn power off to all devices Refer to the instruction before connecting. manual of each device before connecting. Cleaning the Air filter Clean the air filter about every 100 hours. 1 Turn off the MAIN POWER switch of the projector and pull out the power cord.
Cleaning the Air filter (continued) 3 Cleaning the air filter with a vacuum cleaner 4 Installing the air filter (Caution) When the air filter becomes clogged with dust, etc., the projector prevent the internal heat level rising. Do not operate the projector with the air filter removed. power may turn off to] Lamp The light source lamp has a service life. When used for an extended time, the images may become A malfunction The following darker and the colors may deteriorate.
Message table (continued) Indicators The POWER indicator, LAMP indicator and TEMP indicator light or blink in the following POWER indicator LAMP indicator TEMP indicator Lights orange Turns off Turns off Standby status Flashes green Turns off Turns off Warming up Lights green Turns off Turns off Operation status ,1 Flashes orange Turns off Turns off Cool down Message / cases. Processing Wait some time (approx. 20 min.
Specifi cations .These speoi'_oations are sobject tochange without no.ce. Product name Liquid crystal projector Model CP-X960W/E Display method Three liquid crystal panels, three primary color system. Liquid crystal Panel size 3.3 cm (1.3 type) panel Drive system TFT active matrix Number of pixels 786,432 pixels (768 horizontal x1,024 vertical) Lens Zoom lens F=1.7-2.3 Lamp 190w UHB Speaker 1.2W + 1.2W (Stereo) Power supply AC100 ~ 120V, 3.7A / AC220 - 240V, 1.5A.
About the warranty and after-service / About the warranty] A warranty is provided for this product. Fill in the necessary items and store in a safe place. About after-service] When a problem occurs, please check first using the Troubleshooting If the problem still persists, contact your dealer or service company. Chart provided in this instruction manual. About repairs during the warranty period Repairs will be made as described in the warranty. For details, please read the warranty.
