Liquid Crystal Projector CP-SX5500W USER'S MANUAL Please read this user's manual thoroughly to ensure correct usage through understanding. TECHNICAL REGULATORY NOTICES ENGLISH 00CP-SX5500W02 01.10.
01CP-SX5500W02 01.10.24 1:41 PM ページ 1 Liquid Crystal Projector ENGLISH USER'S MANUAL Thank you for purchasing this liquid crystal projector. WARNING • Please read the accompanying manual “SAFETY INSTRUCTIONS” and this “USER'S MANUAL” thoroughly to ensure correct usage through understanding. After reading, store this instruction manual in a safe place for future reference. NOTE • The information in this manual is subject to change without notice.
FEATURES This liquid crystal projector is used to project various computer signals as well as NTSC / PAL / SECAM video signals onto a screen. Little space is required for installation and large images can easily be realized. Outstanding Brightness The UHB lamp and high-efficiency optical system assure a high level of brightness. Partial Magnification Function Interesting parts of images can be magnified for closer viewing. Distortion Correction Function Distortion-free images are quickly available.
01CP-SX5500W02 01.10.24 1:41 PM ページ 4 BEFORE USE (continued) Part Names (continued) BLANK Button STANDBY/ON Button VIDEO Button B STAN DBY/O N LAS K LAN LASER Button ER RGB Button B RG Disk Pad MOUSE / RIGHT Button O VIDE Used to operate the mouse shift function and left click function. Used to click the right mouse button. KEYSTONE Button AUTO Button MENU Button O AUT MENU SELECT Button Used to click the left mouse button. , , , Button Used to operate the mouse shift function.
01CP-SX5500W02 01.10.24 1:41 PM ページ 5 BEFORE USE (continued) Install the AA batteries into the remote control transmitter. 1. Remove the battery cover. Push the knob while lifting up the battery cover. 2. Load the batteries. Make sure the plus and minus poles are correctly oriented. 3. Close the battery cover. ENGLISH Loading the Batteries 1 2 CAUTION • Use only the specified batteries with this remote control transmitter. Also, do not mix new and old batteries.
01CP-SX5500W02 01.10.24 1:41 PM ページ 6 INSTALLATION Installation of the Projector and Screen Refer to the drawing and table below for determining of the screen size and projection distance. The projection distances shown in the table below are for full size (1365 x 1024 dots). a: Distance from the projector to the screen. (±10%) Screen Table 1. Installation Reference Screen size [inches (m)] a [inches (m)] Min. Max. 40 (1.0) 60 (1.5) 65 (1.6) 98 (2.5) 85 (2.2) 127 (3.2) 80 (2.0) 131 (3.3) 170 (4.
01CP-SX5500W02 01.10.24 1:41 PM ページ 7 INSTALLATION (continued) ENGLISH Cabling Refer to the table below for connecting each terminal of the projector to each device. Table 2.
01CP-SX5500W02 01.10.24 1:41 PM ページ 8 INSTALLATION (continued) Power Connection Use the correct one of the enclosed power cords depending on the power outlet to be used. Connect the AC inlet of the projector to the power outlet firmly by the power cord. CAUTION • Be carful in handling the power cord according to instructions of the accompanying manual "SAFETY INSTRUCTIONS" and this manual. • Connect the power cord firmly. Avoid using a loose, unsound outlet or contact failure.
ENGLISH OPERATIONS Power ON 1. Check that the power cord is connected correctly. 2. Set the power switch to [ | ]. The standby mode is selected, and the STANDBY/ON indicator is turned to orange. 3. Press the STANDBY/ON button on the control panel or the remote control transmitter. Warm-up begins and the STANDBY/ON indicator blinks in green. 4. The STANDBY/ON indicator ceases blinking and turns to green when power is on. Remove the lens cap. 5. Adjust picture size using the Zoom Knob. 6.
01CP-SX5500W02 01.10.26 6:36 PM ページ 10 OPERATIONS (continued) Basic Operation The basic operations shown in Table 3 is performed from the supplied remote control transmitter or the projector control panel. Items indicated by (*) may be used from the control panel. Table 3 . Basic Operation Item Description Select RGB Input : Press the RGB button. VIDEO/S-VIDEO/COMPONENT VIDEO → RGB IN 1/RGB IN 2/DVI RGB IN 1 → RGB IN 2 → DVI (→ RGB IN 1) INPUT Select Video Input : Press the VIDEO button.
01CP-SX5500W02 01.10.24 1:41 PM ページ 11 OPERATIONS (continued) ENGLISH Items indicated by (*) may be used from the control panel. Table 3. Basic Operation (continued) Item Description VOLUME Volume Adjustment : Press the VOLUME MUTE Set/Clear Mute Mode : Press the MUTE button. No sound is heard in the MUTE mode. AUTO / button. Automatic Adjustment at RGB Input : Press the AUTO button. Horizontal position(H.POSIT), vertical position (V.POSIT),clock phase (H.PHASE), and horizontal size(H.
01CP-SX5500W02 01.10.24 1:42 PM ページ 12 OPERATIONS (continued) Setup Menu SETUP The following adjustments and settings are possible when SETUP is selected at the top of the menu. Part of the Setup menu differs between RGB input and video input. Select an item with the and buttons, and start operation. Use the Single menu to reduce menu size (see Table 3, MENU SELECT). Table 4. Setup Menu Item INPUT BRIGHT CONTRAST V POSIT H POSIT H PHASE H SIZE COLOR BAL R COLOR BAL B ASPECT IMAGE OPT.
01CP-SX5500W02 01.10.24 1:44 PM ページ 13 Input Menu The following functions are available when INPUT is selected on the menu. Select an item with the and buttons, and start or stop operation with the and buttons. The function indicated (**) are effective on video input mode only, not on RGB input mode, except in the P.IN P. window on RGB input mode. SETUP INPUT AUTO RGB VIDEO Progressive BLACK HDTV IMAGE OPT. EXECUTE CANCEL Table 5.
01CP-SX5500W02 01.10.24 1:44 PM ページ 14 OPERATIONS (continued) Image Menu SETUP The following adjustments and settings are available when IMAGE is selected on the menu. Select an item with the and buttons, and start or stop operation with the and buttons. BLANK MIRROR START UP P. IN P.POSIT P.IN P.INPUT GAMMA INPUT IMAGE OPT. Table 6. Image Menu Item Description Select Blank Screen Color: Select color with the and buttons.
01CP-SX5500W02 01.10.24 1:44 PM ページ 15 Options Menu SETUP The following adjustments and settings are available when OPT. is selected on the menu. Select an item with the and buttons, and start or stop operation with the and buttons. The function indicated (**) are effective on video input mode only, not on RGB input mode, except in the P.IN P. window on RGB input mode. INPUT IMAGE OPT. 16 VOLUME MENU COLOR LANGUAGE AUTO OFF SYNC ON G WHISPER Table 7.
01CP-SX5500W02 01.10.24 1:39 PM ページ 16 OPERATIONS (continued) No Signal Menu The same adjustments and settings are available as with the Image and Options menus when the MENU button is pressed during display of the “NO INPUT IS DETECTED ON ***” or “SYNC IS OUT OF RANGE ON ***” message while no signal is received. Table 8.
01CP-SX5500W02 01.10.24 1:39 PM ページ 17 Lamp HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE Contact your dealer before replacing the lamp. For the optional lamp, see the item “Optional Parts” of the Table 12. Before replacing the lamp, switch power OFF, remove the power cord from the power outlet, and wait approximately 45 minutes until the lamp has cooled. The lamp may explode if handled at high temperatures. WARNING • For disposal of used lamp, treat according to the instruction of community authorities.
01CP-SX5500W02 01.10.24 1:39 PM ページ 18 MAINTENANCE (continued) Replacing the Lamp 1. Switch the projector OFF, remove the power cord from the power outlet, and wait at least 45 minutes for the unit to cool. 2. Prepare a new lamp. 3. Check that the projector has cooled sufficiently, and gently turn it upside down. 4. Loosen the two screws as shown in the diagram, and remove the lamp cover. 5. Loosen the two screws, and gently remove the lamp while holding the grips.
01CP-SX5500W02 01.10.24 1:39 PM ページ 19 Air Filter CP-SX5500 Replacing the Air Filter Replace the air filter if contamination cannot be removed, or if it is damaged. ENGLISH MAINTENANCE (continued) Filter box 1. Remove the filter lid. 2. Pull and remove the old filter from the filter box. 3. Insert the new filter to the filter box. Push left and right edges of the filter with fingers in order to fit the filter to the box properly.
01CP-SX5500W02 01.10.24 1:39 PM ページ 20 TROUBLESHOOTING OSD Message The messages as described below may appear on the screen at power ON. Take the appropriate measures when such a message appears. Table 9. OSD Messages Message Contents The message shown at left appears after the lamp has been used for more than 1300 hours. CHANGE THE LAMP The lamp is approaching the end of its life. AFTER REPLACING LAMP, Power is switched OFF automatically when the lamp RESET THE LAMP TIME.
01CP-SX5500W02 01.10.24 1:39 PM ページ 21 Indicators Message The POWER indicator, LAMP indicator, and TEMP indicator are lit and blank as follows. Take the appropriate measures. Table 10. Indicators Message STANDBY/ON LAMP TEMP indicator indicator indicator Contents Lights orange Turns off Turns off The Standby mode has been set. Blinks green Turns off Turns off Warming up. Please wait. Lights green Turns off Turns off ON. Normal operation possible. Blinks orange Turns off Turns off Cooling.
01CP-SX5500W02 01.10.24 1:39 PM ページ 22 TROUBLESHOOTING (continued) Symptom Before requesting repair, check in accordance with the following chart. If the situation cannot be corrected, then contact your dealer. Table 11. Symptom Symptom The power is not turned on. Possible cause Remedy The main power switch is not turned on. Turn on the main power switch. The power cord is disconnected. Plug the power cord into an AC power outlet. The input is not correctly set.
01CP-SX5500W02 01.10.24 1:39 PM ページ 23 ENGLISH SPECIFICATIONS Table 12. Specifications Item Specification Product name Liquid crystal panel Liquid crystal projector Panel size 2.3 cm (0.9 type) Drive system TFT active matrix Pixels 1,397,760 pixels (1365 horizontal x 1024 vertical) Lens Zoom lens F=2.7 ~ 3.1 f=38.0 ~ 49.0 mm Lamp 220 W UHB Speaker 1W Power supply AC100 ~ 120V, 4.0A / AC220 ~ 240V, 1.
01CP-SX5500W02 01.10.24 1:39 PM ページ 24 WARRANTY AND AFTER-SERVICE If a problem occurs with the equipment, first refer to the P.20 “TROUBLESHOOTING” section and run through the suggested checks. If this does not resolve the problem contact your dealer or service company. They will tell you what warranty condition is applied.
09CP-SX5500W02 01.10.23 8:33 PM ページ 1 TECHNICAL 335 Dimension Diagram Unit : mm 118.5 103 250 Signal Connector Pin Assignment 1. D-sub 15-pin Shrink Connector (RGB IN 1/RGB IN 2/RGB OUT) Pin No 1 2 3 4 5 6 7 8 Signal Video input Red Video input Green Video input Blue Ground Ground Red Ground Green Ground Blue Pin No Signal 9 10 11 - 12 13 14 Ground Pin No 15 RGB IN 1: SDA(DDC) RGB IN 2: RGB OUT: H. sync./ Composite sync.
09CP-SX5500W02 01.10.23 8:33 PM ページ 2 TECHNICAL (continued) Example of computer signal Resolution H×V fH (kHz) fV (Hz) Rating 720 × 400 37.9 85.0 VESA TEXT 640 × 480 31.5 59.9 VESA VGA (60Hz) 640 × 480 35.0 66.7 640 × 480 37.9 72.8 VESA VGA (72Hz) 640 × 480 37.5 75.0 VESA VGA (75Hz) 640 × 480 43.3 85.0 VESA VGA (85Hz) 800 × 600 35.2 56.3 VESA SVGA (56Hz) 800 × 600 37.9 60.3 VESA SVGA (60Hz) 800 × 600 48.1 72.2 VESA SVGA (72Hz) 800 × 600 46.9 75.
09CP-SX5500W02 01.10.23 8:33 PM ページ 3 TECHNICAL (continued) Initial set signals The following signals are used for the initial settings. The signal timing of some computer models may be different. In such case, refer to adjust the V.POSIT and H.POSIT of the menu. Back porch b Front porch d Display interval c Back porch b Front porch d Display interval c DATA DATA HSYNC VSYNC Sync a Computer / Signal Sync a Horizontal signal timing (µs) TEXT a 2.0 b 3.0 c 20.3 d 1.
09CP-SX5500W02 01.10.23 8:33 PM ページ 4 TECHNICAL (continued) Connection to the Mouse Control 1. PS/2, ADB or Serial Mouse (1) Turn off the projector and computer, and connect the two units with the appropriate cable. For PS/2 mouse control (for IBM and compatible), use the enclosed mouse cable. For others, consult your dealer. (2) Disconnect the USB cable from the projector if it is connected. Then turn on the projector. (3) Turn on the computer. (4) Start the mouse function.
TECHNICAL (continued) ADB Mouse USB jack (B type) 2 3 1 4 1 2 3 4 ADB (POWER ON) +5V GND Computer Projector +5V 1 1 +5V —DATA 2 2 —DATA +DATA 3 3 GND 4 USB jack (A type) +DATA 4 GND 1 2 3 4 USB cable TECHNICAL - 5 TECHNICAL 1 2 3 4 5 6 RTS 7 8 +5V 9 GND 10 11 12 13 14 15
09CP-SX5500W02 01.10.23 8:33 PM ページ 6 TECHNICAL (continued) RS-232C communication (1) Turn off the projector and computer power supplies and connect with the RS-232C cable. (2) Turn on the computer power supply and, after the computer has started up, turn on the projector power supply.
09CP-SX5500W02 01.10.23 8:33 PM ページ 7 TECHNICAL (continued) Requesting projector status (Get command) (1) Send the request code Header + Command data (‘02H’+‘00H’+ type (2 bytes) +‘00H’+‘00H’) from the computer to the projector. (2) The projector returns the response code ‘1DH’+ data (2 bytes) to the computer. Changing the projector settings (Set command) (1) Send the setting code Header + Command data (‘01H’+‘00H’+ type (2 bytes) + setting code (2 bytes)) from the computer to the projector.
09CP-SX5500W02 01.10.
09CP-SX5500W02 01.10.
09CP-SX5500W02 01.10.
Operation type Header TECHNICAL Names TECHNICAL - 11
09CP-SX5500W02 01.10.
09CP-SX5500W02 01.10.23 8:33 PM ページ 13 REGULATORY NOTICES FCC Statement Warning WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
