Hi sense USER MANUAL Reed the manual carefully and ensure you have fully understood its contents before operating this device for the first time.
| important Notice Paragraphs beginning with the symbol A indicate important instructions, tips or conditions for the following settings. For your own safety and the optimal performance of your TV, ensure to read the safety Instructions before performing any Installation. Compatibility with 3rd party products, software and services are not guaranteed. We cannot be held liable for any damage or loss suffered whilst operating, using or connecting to incompatible devices or apps.
The Intended use and ambient conditions for this TV This TV is intended for the rendering of video and audio signals, on a table-top or wall mounted, In a home or office environment. It must not be used In rooms with a high level of humidity or dust concentration. The warranty Is only valid If used as Intended by the manufacturer. Avo High humidity and dust concentration may lead to current leaks in the device.
um Moving/Transportation Before moving this TV, disconnect all cables and move in the vertical position only. Grasp the device on the upper and lower edges of the frame. Do not press or put stress on the front panel of the TV. It may take two or more people to carry larger TVs. If you have to briefly lay down the TV, place the unit with its entire front surface lying fiat on soft material. The screen is made of glass and can break if it is not handled properly. Always wear rubber gloves to Camry the unit.
um Air ventilation and high temperatures Install your TV only where there is proper ventilation, and ensure that thees is at least 10 cm free space on the sides and 20 cm above the unit for air circulation. Excessive heat and obstruction of ventilation could lead to fire or early failure of some electric components. Da not block any ventilation openings with newspapers, tablecloths, curtains, etc. Do not dry clothing ste. on top of the unit.
If you have a cardiac pacemaker, keep a distance of at least 22 cm from the TV. Radio waves may interfere with the operation of a pacemaker. =u Built-In wireless LAN Do not connect to wireless networks that you do not have the usage rights for. Data transmitted and received over radio waves may be intercepted and monitored. The bully-n wireless LAN uses 2.4 GHz and 5 GHz frequency band.
mu Cleaning and care CAUTION: Unplug the power cord prior to cleaning the TV. Clean the TV, the screen, and the remote control with a soft, moist, clean and color-natural cloth only. Do not use any chemicals. Do not subject the surfaces to insect repellent, solvent, thinner or other volatile substances. This may degrade the surface quality. Do not spray water or other liquids directly on the TV. Liquid inside the TV could lead to product failure.
um Notes about prevention from damage of LODE TV screens + Image retention LODE TVs are prone to image retention due to the characteristics of the materials used. If the image repeatedly displays at the same position on the screen, or display time is too long, image retention may occur, which is not a TV malfunction. Please avoid the following operations for a long time, which may cause image retention: There are black bars content on the top, bottom, left, and right of the screen.
Apparatus with CLASS | construction shall be connected to a MAINS socket outlet with a protective earthing connection. Figures and illustrations in this manual are provided for reference only and may differ from actual product appearance. Parts of the software function changes with the system upgrade. ‘LODE TVs are manufactured with the mast sophisticated technology, but you may still sea dark spots or bright spots In the panel (white, red, green or blue).
{ caution + Be sure to disconnect the AC power cord before installing a stand or wall mount brackets. + The display on your TV is fragile. Make sure the TV screen is not scratched or damaged by hard objects or from pressure. + After the installation is completed, make sure the TV is steady on a table or firmly attached to a wall mount, before removing all protective film, if any.
4. Secure the Base Stand to your TV with 4 screws (M5x186). 5. Take off the front cushion and protective plastic bag. And secure the Upper Cover plate to the Base Stand with 4 screws (M4x12). Upper Cover plate 6. Install Cable Cover plates. You can tidy your cables in the slots of the Upper Cover plate, and install Cable Cover plates on the slots. = Cable Cover plates are labeled with L or R, and install according to the label. = Do not let Cable Cover plates nip cables.
1. Lift and nave your TV vertically to the Boston Cushion, and one parson holds your TV to prevent it from falling down. 2. Another person takes off the 4 screws on the back cover of your TV. BI NOTE The screws taken off can not be used for securing wall mount bracket. {: CAUTION When mounting the TV on a wall, follow instructions provided with the wall mount bracket. If it is not comely mounted, the TV may fell and cause property damage or personal injury. * Place spacers between the TV and bracket.
TV Front Remote sensor/Light sensor Power indicator Remote sensor Power Indicator Receive remote signals from the remote control. Do not put anything near the sensor, as its function may be affected. The light is off when the TV is turned on. The light is white in standby mods. Select among the different input signal sources or put the TV in standby mode, or you can tum on the TV when the TV in standby mode. Toggle the OK button left and right to adjust the volume.
TV Rear AC INPUT BI NOTES + ANT Jack supports prows supply for satellite antenna (13/8V, 0.5A max.) + Check the jacks for position and type before making any connections. Loose connections can result in image or color problems. Make sure that all connections are tight and secure. + Not all AV devices have the ability to connect to a TV. Please refer to the user's manual of your A/V device for compatibility and connections procedure.
# LAN (Wired setup) Connect your TV to your network by connecting the LAN port on the back of your TV to an external modem or router using a LAN (Empathetic 5) cable. See the illustration below. It Is recommended to use a made or router that supports Dynamic Host "Configuration Protocol (DHCP). Modems and routers that support CPD automatically provide the IP address, subset mask, gateway, and DNS, so you don't have to enter them manually. Most home networks already have CPD.
Outdoor Antenna Cable wie ce | Antenna Cable (750) {not included) VHF/UHF Antenna ANT ars TR (not included} Sat elite antenna Audio Speakerphone DIGITAL 1] AUDIO OUT Aon DIGITAL AUDIO cable {not included) Audio Ampifier/Spesker Se Ee HR oes HDMI cable (not Included) receiver/ Set-top Box HDMI cable (not Included) AEE eee VCR/DVD Player/ box! it Satellite Receiver/ AN e ete 0 gry “Van Gores {Cables are not included) 0 —p Headphone {not Included) HEADPHONE BI NOTE .
COMMON INTERFACE uss Common rec [ale] <— — Use um DOU RIND. DCS Data. NOTES Before you insertions the Cl+ module, ensure that the TV is switched off. Then insert the CI card into the Cl+ module in accordance with the Service Provider's instructions. Do not repeatedly Insert or remove the Common Access Module as this may damage the Interface and cause a malfunction. You must obtain a Cl+ module and card from the service provider of the channels you want to watch.
(@ @: Receive the voice 2) TEXT: Tum on/off the teletext function INFO: Display the present programmer information @ (2x Switch the TV on or into standby mode @ INPUT: Select input sources (® Number buttons: Direct channel selection or numbers input GUIDE: Display the Electronic Program Guide (DTV mode) (@ CH.
(@ 1% Switch the TV on or into standby mode @ TXT: Tum on/off the teletext function INPUT: Select input sources (@ Number buttons: Direct channel selection or numbers input (5) GUIDE: Display the Electronic Program Guide (DTV mode) CH.
NEG Rode INPUT Sub, (D ¢Lx: Switch the TV on or Into standby mode (@ INFO: Display the present programmer Information @ INPUT: Select Input sources ®@ Custom button to launch input or apps quickly ® 223: All Apps Number buttons: Direct channel selection or numbers input @ ‘GUIDE: Display the Electronic Program Guide (DTV mods) CH.
# Installing Batteries In the Remote Control NOTE: Check information according fo the actual remote control in the accessory bag. 1. Slide the back cover to open the battery compartment of the cremate control. 2. Insert two AAA size batteries. Make sure to match the and { } ends of the batteries with the and ( ) ends Indicated In the battery compartment. 3. Close the battery compartment with the cover. 1. Press the switch and the battery case will pop up automatically. 2. Insert twa AAA size batteries.
% Paling the Remote Control (only for Bluetooth remote control) Pair the remote to the TV after you power it on. Keep the remote control within 3 meters from the TV. Press any button {except power and mic button) to pair. BI NOTES + In special cases, press and hold [E/E] button to pair. If an unknown error occurred with the remote, then it could have been caused by interference. Try to remove what's causing the interference and pair it again.
Turning the TV on for the First Time 1. Connect the mains cable to the mains socket after you have completed all the connections. 2. The first time you tum the TV on, It will go straight Into the Installation Guide. 3. Press the [A] v/ buttons to navigate the menu and change the settings. Press the [OK] button to confirm. Select your Select your desired language to be displayed on the menu. Language Press menu button to set up your TV for store mode.
appearance and specifications are subject to change without notice. Hom Se 55" 65 x 43 inches 57.4 x 34.0 x 43 inches Dimension "Standout o0, , 738 oo mm) | (1457 *HxD 629.0% 11.01 4x39 x N70 THIEF wend am. | (1407 263 298 mm Cola " 474s @15kg) 61.5 Ibs (27.9 kg) With Stand 67.7 Ibs (30.7 kg) 92.6 Ibs (42.0 kg) Active Screen Size Diagonal) 139 om 164 om Screen resolution 3840 x 2160 Audio 6x10W + 2x TOW + 2%20W Operating mode power density 0.043 Watts/cm? | 0.
Recycling/Licenses WERE (Waste Electronic Electric Equipment) European Directive 2012/18/EU “This symbol on the product or on its packaging indicates that this product must not be disposed of with your household waste. Instead, iris your responsibility to dispose of your waste equipment by handing It over to a designated collection point for the recycling of waste electrical and electronic equipment.
dts. For DTS patents, ses Manufactured under license from DTS, Inc. (for companies headquartered In the or under license from DTS Licensing Limited (for all other companies). DTS, D TS-HD Master Audio, D TS-HD, Virtual:X, and the D TS-HD logo are registered trademarks or trademarks of DTS, Inc. in the United States and other countries. © 2020 DTS, Inc. ALL RIGHTS RESERVED. MAX dts Manufactured under license from MAX Corporation.
