USER MANUAL Reed the manual carefully and ensure you have fully understood its contents before operating this device for the first time.
important Notions Paragraphs beginning with the symbol A indicate important instructions, tips or conditions for the following settings. For your own safety and the optimal performance of your TV, ensure to read the safety Instructions before performing any Installation. It is not guarantee operation and performance of peripheral devices made by other manufacturers. We disclaim any liability or damage that may arise from operation and/ or performance from usage of such other maker's peripheral devices.
The Intended use and ambient conditions for this TV This TV is intended for the rendering of video and audio signals, on a table-top or wall mounted, In a home or office environment. It must not be used In rooms with a high level of humidity or dust concentration. The warranty Is only valid If used as Intended by the manufacturer. Avo High humidity and dust concentration may lead to current leaks in the device.
um Moving/Transportation Before moving this TV, disconnect all cables and move in the vertical position only. Grasp the device on the upper and lower edges of the frame. Do not press or put stress on the front panel of the TV. It may take two or more people to carry larger TVs. If you have to briefly lay down the TV, place the unit with its entire front surface lying fiat on soft material. The screen is made of glass and can break if is not handled properly. Always wear rubber gloves to Camry the unit.
um Air ventilation and high temperatures Install your TV only where there is proper ventilation, and ensure that thees is at least 10 cm freak spaces on the sides and 20 cm above the unit for air circulation. Excessive heat and obstruction of ventilation could lead to fire or early failure of some electric components. Da not block any ventilation openings with newspapers, tablecloths, curtains, etc. Do not dry clothing ste. on top of the unit.
If you have a cardiac pacemaker, keep a distance of at least 22 cm from the TV. Radio waves may interfere with the operation of a pacemaker. =u Built-In wireless LAN Do not connect to wireless networks that you do not have the usage rights for. Data transmitted and received over radio waves may be intercepted and monitored. The bully-in wireless LAN uses 2.4 GHz and 5 GHz frequency bands.
mu Cleaning and care CAUTION: Unplug the power cord prior to cleaning the TV. Clean the TV, the screen, and the remote control with a soft, moist, clean and color-natural cloth only. Do not use any chemicals. Do not subject the surfaces to insect repellent, solvent, thinner or other volatile substances. This may degrade the surface quality. Do not spray water or other liquids directly on the TV. Liquid inside the TV could lead to product failure.
Apparatus with CLASS | construction shall be connected fo a MAINS casket outlet with a protective earthing connection. (only for 65%) Figures and Illustrations In this manual are provided for reference only and may differ from actual product appearance. Parts of the software function changes with the system upgrade. Contents Accessories List... Installing the Stand or Wall mount Making Connections... Remote Control... Turing the TV on for the Specifications Other Information...
» Installing the Stand + Be sure to disconnect the A/C power cord before installing a stand or Wall-Mount brackets. + The screen Is very fragile, and must be protected at all mes when Installing the base stand. Be sure that no hard or sharp object, or anything that could scratch or damage the screen, comes Into contact with It. DO NOT exert pressure on the front of the TV at any time because the screen could crack.
4. Secure the Base Stand to the TV with the 4 screws in accessory tightly. » Installing the wall mount bracket 400 x 300 (557) 400 x 400 (657) mm i Wall Mount Bracket Rear cover of the TV Follow instructions provided with the wall mount bracket. BI NOTES + The diameter and length of the screws differ depending on the wall mount bracket model. + Wall mount bracket is optional, your device may not have wall mount bracket, please refer fo the actual accessories.
TV Front Single button (Remote sensor / Power indicator / Standby) Item Description Receive remote signals from the remote control. Remote sensor Da not put anything near the sensor, as Its function may be affected. Power indicator The light is red in standby mode. 5 Standby / Source Press the single button when in standby mode, TV will be muted on. Press the single button to call up the menu, when the focus Is on "Power Off", Walt for 3 seconds, then the TV will go Into standby mode automatically.
TV Rear BI NOTES +» ANT Jack supports power supply for satellite antenna (13/18V, 0.5A max.) + Check the jacks for position and type before making any connections. Loose connections can result in image or color problems. Make sure that all connections are tight and secure. + Not all A/V devices have the ability to connect to a TV, please reform fo the user's manual of your A/V device for compatibility and connections procedure.
P LAN (Wired setup) Connect your TV to your network by connecting the LAN port on the back of your TV to an external modem or router using a LAN (Empathetic 5) cable. See the illustration below. © We recommend to use a modem or router that supports Dynamic Host Configuration Protocol (DHCP). Modems and routers that support CPD automatically provide the IP address, subset mask, gateway, and DNS, so you don't have to enter them manually. Most home networks already have CPD.
ve TT Outdoor n= or ROY. ® ‘Antenna Cabin (7602) (not included} VHF Antenna Eo = (not Included) Sat elite antenna Audio Amplifier/Speaker no mi.
BI NOTES Before you insert/remove the Cl+ module, ensure that the TV is switched off. Then insert the CI card into the Cl+ module in accordance with the Service Provider's instructions. Do not repeatedly insert or remove the Common Access Module as this may damage the interface and cause a malfunction. + You must obtain a Cl+ module and card from the service provider of the channels you want to watch. Insert the Cl+ module with the Smart Card in the direction marked on the module and Smart Card.
POWER: Switch the TV on or Into standby mode INPUT: Select input sources TEXT: Tum on/off the teletext function Number bunion: Direct channel selection or numbers input GUIDE: Display the Electronic Program Guide (DTV mode) CH.
POWER: Switch the TV on or Into standby mode INPUT: Select input sources INFO: Display the present program information All Apps Custom button to launch input or apps quickly Number button: Direct channel selection or numbers input GUIDE: Display the Electronic Program Guide (DTV mode) CH.
NFO INPUT © ROO OPPOSITE 666 © 0 POWER: Switch the TV on or Into standby mode INPUT: Select input sources INFO: Display the present program information All Apps Custom button to launch input or apps quickly Number button: Direct channel selection or numbers input GUIDE: Display the Electronic Program Guide (DTV mode) CH.List: Display the Channel List on the screen Display the Quick setup menu Special function buttons.
» Installing Batteries in the Remote Control NOTE: Check information according to the actual remote control in the accessory bag. 1. Slide the back cover to open the battery compartment of the remote control. €2 2. Insert two AAA size batteries. Make sure to match by 0 the and ( ) ends of the batteries with the and { } ends indicated in the battery compartment. 3. Close the battery compartment with the cover. 1. Press the switch and the battery case will pop up = automatically. 2.
Turning the TV on for the First Time 1. Connect the mains cable to the mains socket after you have completed all the connections. 2. The first time you tum the TV on, It will go straight Into the Installation Guide. 3. Press the buttons to navigate the menu and change the settings. Press the [OK] button to confirm. Select your desired language to be displayed on the menu. Select “Home Mode” or “Store Mode”.
Ef Features, appearance and specifications are subject to change without notice. 557 48.5% 20.0 x 3.3 inches (1232 x 736 x 83 mm) 48.5 x 31.5 x12.1 inches (1232 x 799 x 308 mm) 38.4 1bs (17.4 kg) 41.7 Ibs (18.9 kg) 139 cm 3840 x 2160 0.0316 Watts/cm? <05W 0.5wW a5wW 10W + 10W 10W + 10W Pleads refer to the rating label. Please refer to the rating label. B/G, |, B/G DB-C, WF-M68A-UWF1 DBMS DBMS Band) DBMS Band) DBMS Non EU} DBMS WF-M68A-UWF1 65" 67.2% 33.9 x 3.5 inches (1452 x 862 x 89 mm) 57.2 % 36.8 x 14.
Recycling/Licenses WERE (Waste Electronic Electric Equipment} European Directive 2012/18/EU Batteries This symbol on the product or on its packaging indicates that this product must not be disposed of with your household waste. Instead, It Is your responsibility to dispose of your waste equipment by handing It over to a designated collection point for the recycling of waste electrical and electronic equipment.
