User's Manual
Table Of Contents
- Installation
- Contents
- Safety instructions
- General safety instructions
- Certified usage
- Installation site requirements
- Device casing
- Qualification requirements for personnel
- National and international safety regulations
- Grounding the device
- Lightning protection
- Requirements for connecting electrical wires
- Requirements for connecting the supply voltage
- ATEX directive 2014/34/EU – specific regulations for safe operation
- Relevant for use in explosion hazard areas (Hazardous Locations, Class I, Division 2):
- E marking
- CE marking
- LED or laser components
- FCC note
- Note for the use in the Japan
- Note for the use in Oman
- Recycling note
- About this manual
- Key
- 1 Description
- 1.1 General description
- 1.2 Device name and product code
- 1.3 Device view
- 1.4 Power supply
- 1.4.1 Supply voltage with the characteristic value C (24 V DC ... 48 V DC)
- 1.4.2 Supply voltage with the characteristic value K (60 V DC ... 250 V DC / 110 V AC ... 230 V AC, 50 Hz ... 60 Hz)
- 1.4.3 Supply voltage with the characteristic value P (Power supply only through PoE)
- 1.4.4 Supply voltage with the characteristic value W (24 V DC)
- 1.5 Ethernet ports
- 1.6 Connections for antennas
- 1.7 Display elements
- 1.8 Management interfaces
- 1.9 Signal contact
- 1.10 Reset button
- 2 Installation
- 3 Making basic settings
- 4 First login (Password change)
- 5 Obtain compliance for operation in the European Union
- 6 Configuring the transmit power
- 7 Configuring the transmit power for the 4.9 GHz band
- 8 Maintenance and service
- 9 Disassembly
- 10 Technical data
- 10.1 General technical data
- 10.2 Dimension drawings
- 10.3 Radio technology
- 10.4 Roaming
- 10.5 Receiving sensitivity, transmit power, and data rate of the WLAN module version EWLAN1 (Approvals 2, characteristic value M or 9)
- 10.6 Receiving sensitivity, transmit power, and data rate of the WLAN module version EWLAN1 for device variants with approval for the 4.9 GHz band (Approvals 2, characteristic value P)
- 10.7 Receiving sensitivity, transmit power, and data rate of the WLAN module version EWLAN2 for high-gain antennas (Approvals 2, characteristic value H)
- 10.8 EMC and immunity
- 10.9 Network range
- 10.10 Power consumption/power output
- 11 Scope of delivery, order numbers and accessories
- 12 Underlying technical standards
- A Further support
Installation BAT-F
Release
18
07/2020
73
10.6 Receiving sensitivity, transmit power, and
data rate of the WLAN module version
EWLAN1 for device variants with approval
for the 4.9 GHz band (Approvals 2,
characteristic value P)
Applies exclusively to WLAN module version EWLAN1 for device variants
with approval for the 4.9 GHz band (Approvals 2, characteristic value P)
according to FCC 47CFR Part 90 Subpart Y.
The values shown in the following tables show measured maximum values
in the lowest channel of the respective bandwidth with 1 active antenna. The
values are in no case to be perceived as a guaranteed property of the overall
product. Depending on the settings, the module automatically reduces the
data rate and transmit power according to FCC 47CFR Part 90 Subpart Y.
10.6.1 IEEE 802.11a, Bandwidth 5 MHz
10.6.2 IEEE 802.11a, Bandwidth 10 MHz
IEEE 802.11a
Frequency range 4.940 GHz to 4.990 GHz
Bandwidth 5 MHz
Data rate Typical transmit power
1.5 Mbit/s 13 dBm
2.25 Mbit/s 13 dBm
3 Mbit/s 13 dBm
4.5 Mbit/s 13 dBm
6 Mbit/s 13 dBm
9 Mbit/s 12 dBm
12 Mbit/s 12 dBm
13.5 Mbit/s 11 dBm
Table 18: IEEE 802.11a, Frequency range 4.940 GHz to 4.990 GHz, Bandwidth
5 MHz, Channels 218-227
IEEE 802.11a
Frequency range 4.940 GHz to 4.990 GHz
Bandwidth 10 MHz
Data rate Typical transmit power
3 Mbit/s 14 dBm
4.5 Mbit/s 14 dBm
6 Mbit/s 14 dBm
Table 19: IEEE 802.11a, Frequency range 4.940 GHz to 4.990 GHz, Bandwidth
10 MHz, Channels 19-27