User's Manual
Table Of Contents
- Installation
- Contents
- Safety instructions
- General safety instructions
- Certified usage
- Installation site requirements
- Device casing
- Qualification requirements for personnel
- National and international safety regulations
- Grounding the device
- Lightning protection
- Requirements for connecting electrical wires
- Requirements for connecting the supply voltage
- ATEX directive 2014/34/EU – specific regulations for safe operation
- Relevant for use in explosion hazard areas (Hazardous Locations, Class I, Division 2):
- E marking
- CE marking
- LED or laser components
- FCC note
- Note for the use in the Japan
- Note for the use in Oman
- Recycling note
- About this manual
- Key
- 1 Description
- 1.1 General description
- 1.2 Device name and product code
- 1.3 Device view
- 1.4 Power supply
- 1.4.1 Supply voltage with the characteristic value C (24 V DC ... 48 V DC)
- 1.4.2 Supply voltage with the characteristic value K (60 V DC ... 250 V DC / 110 V AC ... 230 V AC, 50 Hz ... 60 Hz)
- 1.4.3 Supply voltage with the characteristic value P (Power supply only through PoE)
- 1.4.4 Supply voltage with the characteristic value W (24 V DC)
- 1.5 Ethernet ports
- 1.6 Connections for antennas
- 1.7 Display elements
- 1.8 Management interfaces
- 1.9 Signal contact
- 1.10 Reset button
- 2 Installation
- 3 Making basic settings
- 4 First login (Password change)
- 5 Obtain compliance for operation in the European Union
- 6 Configuring the transmit power
- 7 Configuring the transmit power for the 4.9 GHz band
- 8 Maintenance and service
- 9 Disassembly
- 10 Technical data
- 10.1 General technical data
- 10.2 Dimension drawings
- 10.3 Radio technology
- 10.4 Roaming
- 10.5 Receiving sensitivity, transmit power, and data rate of the WLAN module version EWLAN1 (Approvals 2, characteristic value M or 9)
- 10.6 Receiving sensitivity, transmit power, and data rate of the WLAN module version EWLAN1 for device variants with approval for the 4.9 GHz band (Approvals 2, characteristic value P)
- 10.7 Receiving sensitivity, transmit power, and data rate of the WLAN module version EWLAN2 for high-gain antennas (Approvals 2, characteristic value H)
- 10.8 EMC and immunity
- 10.9 Network range
- 10.10 Power consumption/power output
- 11 Scope of delivery, order numbers and accessories
- 12 Underlying technical standards
- A Further support
68
Installation BAT-F
Release
18
07/2020
10.3 Radio technology
10.4 Roaming
IEEE 802.11F (Inter-Access Point Protocol)
IEEE 802.11r (Fast Roaming)
PMK caching
Pre authentification
OKC (Opportunistic key caching)
Antenna connection For each WLAN module: 3 × N socket
Range Depending on the antenna used, frequency range and data rate
Encryption
IEEE 802.11i/WPA2 with passphrase or IEEE 802.1x and
hardware-accelerated AES
Closed Network
WEP 64
a
WEP 128
b
WEP 152
c
User authentication
802.1x/EAP
LEPS
WPA1/TKIP
d
For more information, see the HiLCOS data sheet.
a. With encryptions of the type TKIP and WEP, the device falls back on IEEE 802.11b/g or
IEEE 802.11a.
b. With encryptions of the type TKIP and WEP, the device falls back on IEEE 802.11b/g or
IEEE 802.11a.
c. With encryptions of the type TKIP and WEP, the device falls back on IEEE 802.11b/g or
IEEE 802.11a.
d. With encryptions of the type TKIP and WEP, the device falls back on IEEE 802.11b/g or
IEEE 802.11a.
Frequency range
Support of 2.4 GHz: 2412 MHz to 2472 MHz (for FCC: 2412 MHz
to 2462 MHz)
Support of 5 GHz: 5180 MHz to 5825 MHz (for FCC: 5180 MHz to
5240 MHz and 5745 MHz to 5825 MHz)
Support of 4.9 GHz (for FCC only): 4940 MHz to 4990 MHz
Modulation technology
OFDM: BPSK, QPSK, 16-QAM, 64-QAM
DSSS/CCK, DSSS/DBPSK, DSSS/DQPSK
Radio topology WLAN Access-Point, Bridge-, Router-, Point-to-Point-, Client-, Client-
Bridge-Mode