User's Manual
Table Of Contents
- Installation
- Contents
- Safety instructions
- General safety instructions
- Certified usage
- Installation site requirements
- Device casing
- Qualification requirements for personnel
- National and international safety regulations
- Grounding the device
- Lightning protection
- Requirements for connecting electrical wires
- Requirements for connecting the supply voltage
- ATEX directive 2014/34/EU – specific regulations for safe operation
- Relevant for use in explosion hazard areas (Hazardous Locations, Class I, Division 2):
- E marking
- CE marking
- LED or laser components
- FCC note
- Note for the use in the Japan
- Note for the use in Oman
- Recycling note
- About this manual
- Key
- 1 Description
- 1.1 General description
- 1.2 Device name and product code
- 1.3 Device view
- 1.4 Power supply
- 1.4.1 Supply voltage with the characteristic value C (24 V DC ... 48 V DC)
- 1.4.2 Supply voltage with the characteristic value K (60 V DC ... 250 V DC / 110 V AC ... 230 V AC, 50 Hz ... 60 Hz)
- 1.4.3 Supply voltage with the characteristic value P (Power supply only through PoE)
- 1.4.4 Supply voltage with the characteristic value W (24 V DC)
- 1.5 Ethernet ports
- 1.6 Connections for antennas
- 1.7 Display elements
- 1.8 Management interfaces
- 1.9 Signal contact
- 1.10 Reset button
- 2 Installation
- 3 Making basic settings
- 4 First login (Password change)
- 5 Obtain compliance for operation in the European Union
- 6 Configuring the transmit power
- 7 Configuring the transmit power for the 4.9 GHz band
- 8 Maintenance and service
- 9 Disassembly
- 10 Technical data
- 10.1 General technical data
- 10.2 Dimension drawings
- 10.3 Radio technology
- 10.4 Roaming
- 10.5 Receiving sensitivity, transmit power, and data rate of the WLAN module version EWLAN1 (Approvals 2, characteristic value M or 9)
- 10.6 Receiving sensitivity, transmit power, and data rate of the WLAN module version EWLAN1 for device variants with approval for the 4.9 GHz band (Approvals 2, characteristic value P)
- 10.7 Receiving sensitivity, transmit power, and data rate of the WLAN module version EWLAN2 for high-gain antennas (Approvals 2, characteristic value H)
- 10.8 EMC and immunity
- 10.9 Network range
- 10.10 Power consumption/power output
- 11 Scope of delivery, order numbers and accessories
- 12 Underlying technical standards
- A Further support
54
Installation BAT-F
Release
18
07/2020
5 Obtain compliance for operation in the
European Union
For operation in the European Union, the device must comply with the Radio
Equipment Directive (RED) 2014/53/EU. The RED compliance requires
compliant operation of the device in the 5 GHz band channels. Compliant
operation of the device is achieved by an unchangeable determination of the
country setting.
Make the country setting unchangeable using the Command Line Interface
(CLI), the graphical user interface or the LANconfig software. You can
download the LANconfig software from the Hirschmann product pages
(www.hirschmann.com).
Perform the following work steps:
Command Line Interface (CLI)
To access the possible country settings, execute the following
command:
set Setup/WLAN/Country ?
Note: The country setting “Europe” is valid for all European countries.
Specific country settings such as “France” or “Germany” include
additional country specific channels in comparison to the “Europe”
country setting.
The device ignores specific country settings and uses the country
setting “Europe” until the RED compliance has been obtained.
Select the desired country setting with the following command:
set Setup/WLAN/Country [Country]
Example:
set Setup/WLAN/Country France
Execute the following command:
> REDcompliance