User's Manual
Table Of Contents
- Installation
- Contents
- Safety instructions
- General safety instructions
- Certified usage
- Installation site requirements
- Device casing
- Qualification requirements for personnel
- National and international safety regulations
- Grounding the device
- Lightning protection
- Requirements for connecting electrical wires
- Requirements for connecting the supply voltage
- ATEX directive 2014/34/EU – specific regulations for safe operation
- Relevant for use in explosion hazard areas (Hazardous Locations, Class I, Division 2):
- E marking
- CE marking
- LED or laser components
- FCC note
- Note for the use in the Japan
- Note for the use in Oman
- Recycling note
- About this manual
- Key
- 1 Description
- 1.1 General description
- 1.2 Device name and product code
- 1.3 Device view
- 1.4 Power supply
- 1.4.1 Supply voltage with the characteristic value C (24 V DC ... 48 V DC)
- 1.4.2 Supply voltage with the characteristic value K (60 V DC ... 250 V DC / 110 V AC ... 230 V AC, 50 Hz ... 60 Hz)
- 1.4.3 Supply voltage with the characteristic value P (Power supply only through PoE)
- 1.4.4 Supply voltage with the characteristic value W (24 V DC)
- 1.5 Ethernet ports
- 1.6 Connections for antennas
- 1.7 Display elements
- 1.8 Management interfaces
- 1.9 Signal contact
- 1.10 Reset button
- 2 Installation
- 3 Making basic settings
- 4 First login (Password change)
- 5 Obtain compliance for operation in the European Union
- 6 Configuring the transmit power
- 7 Configuring the transmit power for the 4.9 GHz band
- 8 Maintenance and service
- 9 Disassembly
- 10 Technical data
- 10.1 General technical data
- 10.2 Dimension drawings
- 10.3 Radio technology
- 10.4 Roaming
- 10.5 Receiving sensitivity, transmit power, and data rate of the WLAN module version EWLAN1 (Approvals 2, characteristic value M or 9)
- 10.6 Receiving sensitivity, transmit power, and data rate of the WLAN module version EWLAN1 for device variants with approval for the 4.9 GHz band (Approvals 2, characteristic value P)
- 10.7 Receiving sensitivity, transmit power, and data rate of the WLAN module version EWLAN2 for high-gain antennas (Approvals 2, characteristic value H)
- 10.8 EMC and immunity
- 10.9 Network range
- 10.10 Power consumption/power output
- 11 Scope of delivery, order numbers and accessories
- 12 Underlying technical standards
- A Further support
50
Installation BAT-F
Release
18
07/2020
2.6.1 Connecting the power supply through a 7/8"
connector
You find the prescribed tightening torque of the locking screw in General
technical data section on page 63.
Plug the socket into the 7/8" connector on the device.
Enable the supply voltage.
2.6.2 Connecting the power supply through PoE
Only for device variants featuring supply voltage with the characteristic
value P (Power supply only through PoE) or W (24 V DC):
By connecting the supply voltage via PoE, you start the operation of the
device.
2.7 Connecting data cables
2.7.1 Gigabit combo port
10/100/1000 Mbit/s PoE PD port
Further information:
“10/100/1000 Mbit/s PoE PD port” on page 34
Connect the data cables according to your requirements.
The tightening torque of the locking screw is 5.3 lb-in (0.6 Nm).
1000 Mbit/s F/O port
Further information:
“1000 Mbit/s F/O port” on page 35
Make sure that you connect LH ports exclusively with LH ports, SX ports
exclusively with SX ports, and LX ports exclusively with LX ports.
Connect the data cables according to your requirements.
NOTICE
MATERIAL DAMAGE
In a PoE installation, use only devices that comply with the IEEE 802.3af/at
standard.
Failure to follow this instruction can lead to equipment damage.