User's Manual
Table Of Contents
- Installation
- Contents
- Safety instructions
- General safety instructions
- Certified usage
- Installation site requirements
- Device casing
- Qualification requirements for personnel
- National and international safety regulations
- Grounding the device
- Lightning protection
- Requirements for connecting electrical wires
- Requirements for connecting the supply voltage
- ATEX directive 2014/34/EU – specific regulations for safe operation
- Relevant for use in explosion hazard areas (Hazardous Locations, Class I, Division 2):
- E marking
- CE marking
- LED or laser components
- FCC note
- Note for the use in the Japan
- Note for the use in Oman
- Recycling note
- About this manual
- Key
- 1 Description
- 1.1 General description
- 1.2 Device name and product code
- 1.3 Device view
- 1.4 Power supply
- 1.4.1 Supply voltage with the characteristic value C (24 V DC ... 48 V DC)
- 1.4.2 Supply voltage with the characteristic value K (60 V DC ... 250 V DC / 110 V AC ... 230 V AC, 50 Hz ... 60 Hz)
- 1.4.3 Supply voltage with the characteristic value P (Power supply only through PoE)
- 1.4.4 Supply voltage with the characteristic value W (24 V DC)
- 1.5 Ethernet ports
- 1.6 Connections for antennas
- 1.7 Display elements
- 1.8 Management interfaces
- 1.9 Signal contact
- 1.10 Reset button
- 2 Installation
- 3 Making basic settings
- 4 First login (Password change)
- 5 Obtain compliance for operation in the European Union
- 6 Configuring the transmit power
- 7 Configuring the transmit power for the 4.9 GHz band
- 8 Maintenance and service
- 9 Disassembly
- 10 Technical data
- 10.1 General technical data
- 10.2 Dimension drawings
- 10.3 Radio technology
- 10.4 Roaming
- 10.5 Receiving sensitivity, transmit power, and data rate of the WLAN module version EWLAN1 (Approvals 2, characteristic value M or 9)
- 10.6 Receiving sensitivity, transmit power, and data rate of the WLAN module version EWLAN1 for device variants with approval for the 4.9 GHz band (Approvals 2, characteristic value P)
- 10.7 Receiving sensitivity, transmit power, and data rate of the WLAN module version EWLAN2 for high-gain antennas (Approvals 2, characteristic value H)
- 10.8 EMC and immunity
- 10.9 Network range
- 10.10 Power consumption/power output
- 11 Scope of delivery, order numbers and accessories
- 12 Underlying technical standards
- A Further support
4
Installation BAT-F
Release
18
07/2020
2 Installation 43
2.1 Checking the package contents 43
2.2 Installing and grounding the device 43
2.2.1 Installing the device onto or on a flat surface 43
2.2.2 Installing the device on a pole 44
2.2.3 Grounding the device 44
2.3 Installing an SFP transceiver (optional) 45
2.4 Installing the antennas 45
2.5 Connecting the power supply and the signal contact lines 46
2.5.1 Supply voltage with the characteristic value C
(24 V DC ... 48 V DC) 47
2.5.2 Supply voltage with the characteristic value K
(60 V DC ... 250 V DC / 110 V AC ... 230 V AC,
50 Hz ... 60 Hz) 47
2.5.3 Supply voltage with the characteristic value W
(24 V DC) 48
2.5.4 Signal contact 49
2.6 Operating the device 49
2.6.1 Connecting the power supply through a 7/8"
connector 50
2.6.2 Connecting the power supply through PoE 50
2.7 Connecting data cables 50
2.7.1 Gigabit combo port 50
2.7.2 10/100/1000 Mbit/s twisted-pair connection (optional) 51
3 Making basic settings 52
4 First login (Password change) 53
5 Obtain compliance for operation in the European
Union 54
6 Configuring the transmit power 57
7 Configuring the transmit power for the 4.9 GHz
band 59
8 Maintenance and service 61