User's Manual
Table Of Contents
- Installation
- Contents
- Safety instructions
- General safety instructions
- Certified usage
- Installation site requirements
- Device casing
- Qualification requirements for personnel
- National and international safety regulations
- Grounding the device
- Lightning protection
- Requirements for connecting electrical wires
- Requirements for connecting the supply voltage
- ATEX directive 2014/34/EU – specific regulations for safe operation
- Relevant for use in explosion hazard areas (Hazardous Locations, Class I, Division 2):
- E marking
- CE marking
- LED or laser components
- FCC note
- Note for the use in the Japan
- Note for the use in Oman
- Recycling note
- About this manual
- Key
- 1 Description
- 1.1 General description
- 1.2 Device name and product code
- 1.3 Device view
- 1.4 Power supply
- 1.4.1 Supply voltage with the characteristic value C (24 V DC ... 48 V DC)
- 1.4.2 Supply voltage with the characteristic value K (60 V DC ... 250 V DC / 110 V AC ... 230 V AC, 50 Hz ... 60 Hz)
- 1.4.3 Supply voltage with the characteristic value P (Power supply only through PoE)
- 1.4.4 Supply voltage with the characteristic value W (24 V DC)
- 1.5 Ethernet ports
- 1.6 Connections for antennas
- 1.7 Display elements
- 1.8 Management interfaces
- 1.9 Signal contact
- 1.10 Reset button
- 2 Installation
- 3 Making basic settings
- 4 First login (Password change)
- 5 Obtain compliance for operation in the European Union
- 6 Configuring the transmit power
- 7 Configuring the transmit power for the 4.9 GHz band
- 8 Maintenance and service
- 9 Disassembly
- 10 Technical data
- 10.1 General technical data
- 10.2 Dimension drawings
- 10.3 Radio technology
- 10.4 Roaming
- 10.5 Receiving sensitivity, transmit power, and data rate of the WLAN module version EWLAN1 (Approvals 2, characteristic value M or 9)
- 10.6 Receiving sensitivity, transmit power, and data rate of the WLAN module version EWLAN1 for device variants with approval for the 4.9 GHz band (Approvals 2, characteristic value P)
- 10.7 Receiving sensitivity, transmit power, and data rate of the WLAN module version EWLAN2 for high-gain antennas (Approvals 2, characteristic value H)
- 10.8 EMC and immunity
- 10.9 Network range
- 10.10 Power consumption/power output
- 11 Scope of delivery, order numbers and accessories
- 12 Underlying technical standards
- A Further support
32
Installation BAT-F
Release
18
07/2020
4 Ethernet port 1
Combo port – you can use these ports for alternative purposes:
4a SFP slot for 1000 Mbit/s F/O connections
Design: IP67-V1 connector according to IEC 61076-3-106, variant 1
4b alternatively, depending on
device variant
Supply voltage with characteristic value C (24 V DC ...
48 V DC) and K (60 V DC ... 250 V DC / 110 V AC ...
230 V AC, 50 Hz ... 60 Hz):
8-pin, “X”-coded M12 socket for 10/100/1000 Mbit/s
twisted pair connections
Supply voltage with characteristic value P (Power
supply only through PoE) and W (24 V DC):
8-pin, “X”-coded M12 socket for 10/100/1000 Mbit/s
PoE PD connections
5 Optional:
Ethernet port 2
8-pin, “X”-coded M12 socket for 10/100/1000 Mbit/s
twisted pair connections
6 8-pin, “A”-coded M12 socket for V.24 interface
7 5-pin, “A”-coded M12 socket for USB interface
8 alternatively, depending on
device variant
Approvals 1 with characteristic value F and G:
The reset button below a screwable IP67 pressure
compensating cap
Approvals 1 with characteristic value I, K, M and 9:
Reset button behind a screwable IP65/67 protection
cap
9 Only for device variants featuring supply voltage with characteristic value C (24 V DC ...
48 V DC), K (60 V DC ... 250 V DC / 110 V AC ... 230 V AC, 50 Hz ... 60 Hz) or W
(24 V DC):
4-pin, “A”-coded M12 plug for signal contact
10 Supply voltage connection 1
alternatively, depending on
device variant
Supply voltage with characteristic value C (24 V DC ...
48 V DC)
4-pin, 7/8" connector
Supply voltage with characteristic value K (60 V DC ...
250 V DC / 110 V AC ... 230 V AC, 50 Hz ... 60 Hz)
3-pin, 7/8" connector
Supply voltage with characteristic value P (Power
supply only through PoE):
Not present
Supply voltage with characteristic value W (24 V DC):
4-pin, 7/8" connector
11 Supply voltage connection 2
alternatively, depending on
device variant
Supply voltage with characteristic value C (24 V DC ...
48 V DC)
4-pin, 7/8" connector
Supply voltage with characteristic value K (60 V DC ...
250 V DC / 110 V AC ... 230 V AC, 50 Hz ... 60 Hz)
3-pin, 7/8" connector
Supply voltage with characteristic value P (Power
supply only through PoE):
Not present
Supply voltage with characteristic value W (24 V DC):
4-pin, 7/8" connector
12 Connection for protective ground