User's Manual
Table Of Contents
- Installation
- Contents
- Safety instructions
- General safety instructions
- Certified usage
- Installation site requirements
- Device casing
- Qualification requirements for personnel
- National and international safety regulations
- Grounding the device
- Lightning protection
- Requirements for connecting electrical wires
- Requirements for connecting the supply voltage
- ATEX directive 2014/34/EU – specific regulations for safe operation
- Relevant for use in explosion hazard areas (Hazardous Locations, Class I, Division 2):
- E marking
- CE marking
- LED or laser components
- FCC note
- Note for the use in the Japan
- Note for the use in Oman
- Recycling note
- About this manual
- Key
- 1 Description
- 1.1 General description
- 1.2 Device name and product code
- 1.3 Device view
- 1.4 Power supply
- 1.4.1 Supply voltage with the characteristic value C (24 V DC ... 48 V DC)
- 1.4.2 Supply voltage with the characteristic value K (60 V DC ... 250 V DC / 110 V AC ... 230 V AC, 50 Hz ... 60 Hz)
- 1.4.3 Supply voltage with the characteristic value P (Power supply only through PoE)
- 1.4.4 Supply voltage with the characteristic value W (24 V DC)
- 1.5 Ethernet ports
- 1.6 Connections for antennas
- 1.7 Display elements
- 1.8 Management interfaces
- 1.9 Signal contact
- 1.10 Reset button
- 2 Installation
- 3 Making basic settings
- 4 First login (Password change)
- 5 Obtain compliance for operation in the European Union
- 6 Configuring the transmit power
- 7 Configuring the transmit power for the 4.9 GHz band
- 8 Maintenance and service
- 9 Disassembly
- 10 Technical data
- 10.1 General technical data
- 10.2 Dimension drawings
- 10.3 Radio technology
- 10.4 Roaming
- 10.5 Receiving sensitivity, transmit power, and data rate of the WLAN module version EWLAN1 (Approvals 2, characteristic value M or 9)
- 10.6 Receiving sensitivity, transmit power, and data rate of the WLAN module version EWLAN1 for device variants with approval for the 4.9 GHz band (Approvals 2, characteristic value P)
- 10.7 Receiving sensitivity, transmit power, and data rate of the WLAN module version EWLAN2 for high-gain antennas (Approvals 2, characteristic value H)
- 10.8 EMC and immunity
- 10.9 Network range
- 10.10 Power consumption/power output
- 11 Scope of delivery, order numbers and accessories
- 12 Underlying technical standards
- A Further support
22
Installation BAT-F
Release
18
07/2020
To reduce potential radio interference to other users, the antenna type
and its gain should be so chosen that the equivalent isotropically radiated
power (EIRP) is not more than that permitted for successful
communication.
This device has been designed to operate with the antennas listed below
having a maximum gain of 18 dBi:
The FCC approval is valid only in conjunction with the listed antennas. If
other antennas are used, the approval expires. The responsibility lies with
the operator of the system. The required antenna impedance is 50 .
Note for the use in the Japan
This note applies to BAT-F variants with the characteristic
value JP (Japan) for country approvals that are labeled as follows:
"Contains MIC ID: 204-310014"
Devices with the characteristic value JP for country approvals are suitable
for usage with the following antennas:
Antenna(s) for operation with this
device:
Permitted band of operation
2.4 GHz band 5.18 GHz ...
5.24 GHz band
5.745 GHz ...
5.825 GHz band
BAT-ANT-RSMA-2AGN-R
a
a. Note: When using 3 antennas type BAT-ANT-RSMA-2AGN-R, you must align each antenna
in another spatial direction (x-y-z) so that one antenna is arranged vertically to the device
and the other two antennas are arranged at right angles to each other.
Yes Yes Yes
BAT-ANT-N-3AGN-IP67 Yes Yes Yes
BAT-ANT-N-MiMoDB-5N-IP65 Yes Yes Yes
BAT-ANT-N-MiMo5-9N-IP65 No Yes Yes
BAT-ANT-N-8G-DS-IP65 Yes No No
BAT-ANT-N-MiMo-18N-IP65
b
b. Note: Connect the BAT-ANT-N-MiMo-18N-IP65 to the WLAN module as follows:
Connect the antenna port "Ver" with the WLAN-antenna-port 1.
Connect the antenna port "+45 °" with the WLAN antenna port 2.
Connect the antenna port "-45 °" with the WLAN antenna port 3.
Connect the BAT-ANT-N-MiMo-18N-IP65 antenna in this way exclusively.
Differing connection configurations are illegal.
No No Yes
Antennas for operation with this device: Permissible frequency bands
2.4 GHz band 5 GHz band
BAT-ANT-N-3AGN-IP67 Yes Yes
BAT-ANT-RSMA-2AGN-R Yes Yes
BAT-ANT-6ABG-IP65 Yes Yes
BAT-ANT-N-MiMoDB-5N-IP65 Yes Yes
BAT-ANT-N-8G-DS-IP65 Yes No
BAT-ANT-N-9A-DS-IP65 No Yes
BAT-ANT-N-6G-IP65 Yes No
„5GHz band: この製品は屋内においてのみ使用可能です“