User Guide

ManualsBrandsHIRO ManualsComputers & AccessoriesV92 56K External USB Data Fax Dial Up Internet Modem Dual Port Built in Buzzer Truly Plug n Play Driverless Installation Built in Driver Windows 10, 8.1, 8, 7, 32-bit 64-bit

Chapter 1 Introduction ...............................................................................................

1.1 Specifications..........................................................................................................

1.2 Package Content.....................................................................................................

Chapter 2 Installation Guide ......................................................................................

2.1 Hardware Installation (Windows10 8.1 8 7).............................................................

• 1 x USB Modem

• 1 x CD

• 1 x RJ-11 Cable

This chapter contains detailed instructions how to install and configure the

56Kbps USB modem, as well as how to verify if your installation is correct.

We recommend that you follow the steps accordingly to avoid future problems.

ESD Precautions

Electrostatic discharge (ESD) can damage your processor, disk drives, expansion

boards, and other system components. Always observe the following precautions

before you install any system component.

1. Do not remove a component from its protective packaging until you are ready to

install it.

2. Wear a wrist grounding strap and attach it to a metal part of the system unit before

handling components. If a wrist strap is not available, maintain contact with the

system unit throughout any procedure requiring ESD protection.

Installing the 56Kbps USB Modem

1. Turn off the System and unplug the AC power supply from the system.

2. Please connect USB modem directly to a PC with USB cable.

3. Please connect 56Kbps USB modem to the telephone line and telephone set, as

following procedures.

a. Locate an available RJ-11 modular jack telephone outlet.

b. Insert one end of the modular cord that came with your USB 56Kbps modem into

the RJ-11 modular jack marked “LINE” on the modem. Then plug the otherend into

the modular jack on wall outlet. See below Figure.

c. Plug the RJ-11 jack of the telephone set into the RJ-11 jack marked “PHONE” on the

modem, if required. See below figure.

d. If telephone set connected with 56Kbps USB modem via a telephone cord, lift

the telephone handset, and check for a dial tone.

1. Plug the adapter to an available USB port of your computer.

2. The Driver will be automatically found and installed

Interface Standards: USB 2.0

Fax Compatibility ITU-T: Send & Receive Rates up to 14.4k bps.

-V.17, V.29, V.27 ter & V.21 Channel 2

-EIA/TIA 578 Class 1 & T.31 Class 1.0 Commands

Data Transmission: Receive Rates up to 56k bps & Send Rates up to 48k bps (V.92

Mode) or up to 33.6k bps (V.90 Mode)

-ITU-T V.92, V.90, V.34, V.32bis, V.32, V.22bis, V.22, V.23 & V. 21; Bell 212A & Bell 103

-PCM Upstream (V.92 Mode)

-Quick Connect (V.92 Mode)

-Modem-on-hold (V.92 Mode)

-V.250 and V.251 Commands

Error Correction: V.42 LAPM & MNP2-4

Data Compression

-V.44 Data Compression for Optimal Downloading of Internet Web Pages & Files (V.92 Mode)

-V.42 bis & MNP5 Data Compression

LED Indicator

-On: Modem is Off-Hook

-Blink: Data transmission

Wall Jack

Line

Phone

Telephone

Set

Contents

1.2 Package Content

Hardware Setup

2.1 Hardware Installation (Windows 10 8.1 8 7)

Chapter 1 - Introduction

Chapter 2 - Installation Guide

1.1 Specifications

Quick Installation Guide

Manual

Information in this docutment is subject to change without prior notice.

For more information, please go to www.hiroinc.com

V92 56K External

USB Modem

Summary of content (3 pages)

PAGE 1
.2 Package Content • 1 x USB Modem • 1 x CD • 1 x RJ-11 Cable Chapter 2 - Installation Guide Manual Quick Installation Guide V92 56K External USB Modem 2.1 Hardware Installation (Windows 10 8.1 8 7) 1. Plug the adapter to an available USB port of your computer. 2. The Driver will be automatically found and installed Copyright © 2016 by Hiro Inc. All rights reserved. Website: http://www.hiroinc.com Information in this docutment is subject to change without prior notice.
PAGE 2
Commands Most people use the communication software programs to tell modems what to do. Therefore, you may not use the commands in this chapter. However, if you prefer to communicate with your modem directly, you can type the commands described below. Here describes how to work in the terminal mode. Typing Commands Use the BACKSPACE key to delete typing errors. Every command (except A/ and +++) must begin with the AT or at prefix and be entered by pressing the key.
PAGE 3
Commands D commands use pulse dialing until either the T command or a tone dial modifier is received by the modem. Tone dialing is the default setting. This command does not use parameters and generates an ERROR result code when parameters are attached to the command. Q—Result Code Control Result codes are informational messages sent from the modem and displayed on the monitor. Basic result codes include OK, CONNECT, RING, NO CARRIER, and ERROR.