User Manual

493
────────────────────────────────────────────────────
21.1 Error Messages
────────────────────────────────────────────────────
1
2
3
4
5
2
1
7
8
9
1
0
1
1
1
2
1
3
1
4
A
W
ARNING 216：MO drive selected in auto
-
save.
・MO drive selected in auto-save, therefore SCSI cannot
be selected.
W
ARNING 217：SCSI selected in auto-
save.
・Connected SCSI devise selected in auto-save, therefore
MO disk cannot be selected.
W
ARNING 300：Cannot START.
（SYSTEM）
・Cannot start measurement from SYSTEM screen.
W
ARNING 301： Invalid（SYSTEM） ・The key pressed is not valid on the system screen.
W
ARNING 324：Ignore in running．
（AVERAGE）
・Because averaging is used, waveform processing is not
carried out during the start operation.
W
ARNING 325：Invalid．
(Waveform processing)
・The vernier change is disabled for the processed
waveforms.
W
ARNING 327：Invalid．
（COMPARISON）
・Pressed key is invalid, when waveform evaluation is
being carried out.
W
ARNING 328：Invalid．
（OVER LAY）
・Operation is not possible, since the overlay function is
enabled.
W
ARNING 329：Wrong format for
Comparison．
・Since the format is not SINGLE or XY single, a
waveform decision is not possible.
W
ARNING 330：Cannot set．
（SHOT too long）
・The recording length is too long for the memory
segmentation function or a waveform processing
calculation to be carried out.
W
ARNING 334：Cannot set.(AVERAGE) ・Averaging and waveform decision cannot be carried out
.
W
ARNING 335：Cannot set．
（SEQUENTIAL）
・Waveform processing cannot be carried out, because
memory segmentation function is active.
W
ARNING 336：Cannot set．
（MULTI BLOCK）
・Waveform processing cannot be carried out, because
memory segmentation function is active.
W
ARNING 337：Cannot set．
（ROLL MODE）
・Overlay and waveform decision cannot be carried out,
because roll mode is active.
W
ARNING 338：Cannot set．（OVER LAY
）
・Waveform processing cannot be carried out, because
overlay function is active.
W
ARNING 339：Invalid．（STATUS） ・On the status screen, the key pressed is invalid.
W
ARNING 340：Invalid．
（EXT sampling）
・External sampling cannot be carried out.
W
ARNING 345：Cannot set.
(AND logic trigger)
・AND cannot be set between trigger source RMS level
trigger and the logic trigger.
W
ARNING 346：Cannot set.
(AND rms level)
・AND cannot be set between trigger source RMS level
trigger and the logic trigger.
W
ARNING 347：Invalid．(Pre Trigger) ・If no trigger has been set, pre-trigger (0%) is invalid.
W
ARNING 351：Cannot set．（Free run） ・The pre-trigger setting cannot be made, since all trigge
r
sources are switched off (free run).
W
ARNING 352：Invalid．（CHAN） ・On the CHANNEL screen, the key pressed is invalid.
W
ARNING 353：Cannot set.
(time/div:100ms - 5min)
・The voltage drop trigger cannot be used when the time
axis range is 100ms to 5 min/DIV.
W
ARNING 354：Cannot set.
(frequency:133mHz-400Hz)
・The voltage drop trigger is available is a frequency-axis
range of 800 Hz to 400 kHz.
W
ARNING 355：Change time axis.
(RECORDER)
・Since the memory time axis range is delayed, the
recorder time axis is delayed.
W
ARNING 356：Change time axis.
(MEMORY)
・If the speed of the recorder time axis range is increased
beyond two steps below the memory time axis range,
the memory time axis range speed is incremented.
W
ARNING 357：AAF is invalid ・The anti-aliasing filter setting is invalid for the time
axis range of 100 to 500 ｵs and the frequency range of
400 to 80 kHz.