Data Sheet

7
LOGIC PROBE 9320-01
(Accuracy at 23 ±5°C/73 ±9°F, 35 to 80% rh; accuracy guaranteed for 1 year)
Function
Detection of voltage signal or relay contact signal for High/Low state recording
Input
4 channels (common ground between unit and channels), digital/contact input,
switchable
(contact input can detect open-collector signals), input impedance:
1MΩ
(with digital input, 0 to +5V), 500kΩ or more (with digital input, +5 to
+50V)
, pull-up resistance: 2kΩ (contact input: internally pulled up to +5V)
Digital input threshold
1.4V/2.5V/4.0V
Contact input
detection resistance
1.5kΩ or higher (open) and 500Ω or lower (short), 3.5kΩ or higher (open)
and 1.5kΩ or lower
(short), 25kΩ or higher (open) and 8kΩ or lower (short)
Response speed 9320-01: 500ns or lower
Max. allowable input
0 to +50V DC (the maximum voltage that can be applied across input pins without damage)
Cable length and mass: Main unit cable 1.5 m (4.92 ft), input section cable 30 cm
(0.98 ft), approx. 150 g (5.3 oz)
Note: The unit-side plug of the 9320-01 is different from the 9320.
LOGIC PROBE 9321-01
(Accuracy at 23 ±5°C/73 ±9°F, 35 to 80% rh; accuracy guaranteed for 1 year)
Function
Detection of AC or DC relay drive signal for High/Low state recording
Can also be used for power line interruption detection
Input
4 channels (isolated between unit and channels), HIGH/LOW range switching
Input impedance: 100kΩ or higher
(HIGH range), 30kΩ or higher (LOW range)
Output (H)
detection
170 to 250V AC, ±DC (70 to 250V ) (HIGH range)
60 to 150V AC, ±DC (20 to 150V) (LOW range)
Output (L)
detection
0 to 30V AC, ±DC (0 to 43V) (HIGH range)
0 to 10V AC, ±DC (0 to 15V) (LOW range)
Response time
Rising edge 1ms max., falling edge 3ms max. (with HIGH range at 200V
DC, LOW range at 100V DC)
Maximum allowable
input voltage
250Vrms (HIGH range), 150Vrms (LOW range) (the maximum voltage that can
be applied across input pins without damage)
Cable length and mass: Main unit cable 1.5 m (4.92 ft), input section cable 1 m (3.28 ft),
approx. 320 g (11.3 oz) Note: The unit-side plug of the 9321-01 is different from the 9321.
DIFFERENTIAL PROBE 9322
(Accuracy at 23 ±5°C/73 ±9°F, 35 to 80% rh, after 30 minutes of
warm-up time; accuracy guaranteed for 1 year)
Function
For high-voltage floating measurement, power line surge noise
detection, RMS rectified output measurement
DC mode
For waveform monitor output, frequency characteristics: DC to 10MHz
(±3dB), amplitude accuracy: ±1% of full scale (at max. 1000V DC), ±3%
of full scale
(at max. 2000V DC) (full scale: 2000V DC)
AC mode
For detection of power line surge noise, frequency characteristics: 1kHz to 10MHz ±3dB
RMS mode
DC/AC voltage RMS output detection, frequency characteristics: DC, 40Hz
to 100k Hz, response speed: 200ms or less
(400V AC), accuracy: ±1% of full
scale
(DC, 40Hz to 1kHz), ±4% of full scale (1kHz to 100kHz) (full scale: 1000V AC)
Input
Input type: balanced differential input, input impedance/capacitance:
H-L 9MΩ/10pF, H/L-unit 4.5MΩ/20pF, Max. rated voltage to earth:
when using grabber clip 1500V AC/DC
(CAT II ), 600V AC/DC (CAT III),
when using alligator clip: 1000V AC/DC
(CAT II), 600V AC/DC (CAT III)
Maximum allowable input voltage
2000V DC, 1000V AC (CAT II), 600V AC/DC (CAT III)
Output
Voltage divider for 1/1000 of input, BNC connectors (output switchable for 3 modes DC, AC, RMS)
Power source
Power terminal of the input units, or use with AC ADAPTER 9418-15
(DC 12V)
Cable length and mass: Main unit cable 1.3 m (4.27 ft), input section cable 46 cm
(1.51 ft), approx. 350 g (12.3 oz)
■ Specifications of Options (sold separately)
■ Appearance and Dimensions (8807-01 and 8808-01 Instrument-only)
Waveform monitor (5.7 inch color STN LCD)
Screen contrast adjuster
Mass:
8807-01: Approx. 1.1 kg/38.80 oz
8808-01: Approx. 1.2 kg/42.33 oz
Logic probe terminal/for 9320-01 and 9321-01
PC card slot/Type II
Analog input
(Isolated BNC terminal)
8807-01: 2 ch, 8808-01: 4 ch
RS-232C terminal/Mini DIN 9-pin
External trigger input / output
170 mm
(6.69 inch)
203 mm
(7.99 inch)
52 mm
(2.05 inch)
Battery compartment at the rear
LR6/AA alkaline batteries × 6 or 9447 BATTERY PACK × 1
■ Appearance and Dimensions (8807-01 and 8808-01 with printer attached)
Mass: (with 8992 printer attached)
8807-01: Approx. 1.5 kg/59.91 oz
8808-01: Approx. 1.6 kg/56.44 oz
170 mm
(6.69 inch)
280 mm
(11.02 inch)
52 mm
(2.05 inch)
112 mm (4.4 inch) wide thermal printer
(Detachable/option)
■ Supplied accessory PC Software Specifications
Wave Viewer (Wv) Software (Application disk CD-R, bundled accessory)
Functions
• Quick display of waveform files
• Text conversion: Conversion of binary data files to text format, with
storage in either CSV or space/tab delimited format. Span specification
and data culling available.
• Display format settings: scroll function, enlarge/reduce display, display
CH settings.
• Other: Voltage trace function, jump to cursor/trigger position function, etc.
Compatible
operating systems
Windows 95/98/Me or Windows NT 4.0 (SP3 or later), 2000, XP
WAVE PROCESSOR 9335
Distribution media
One CD-R
Operating
environment
Computer equipped with Pentium (133 MHz) or better CPU and at least
32 MB of memory, and running under Windows 95/98/Me, Windows
NT 4.0/2000/XP, or Windows Vista 32-bit type
(recommended system:
Pentium (200 MHz) or better with at least 64 MB of memory)
Display functions
Waveform display/X-Y display/digital value display/cursor function/
scroll function/maximum number of channels (32 channels analog, 32
channels logic)/gauge display (time, voltage axes)/graphical display
File loading
Readable data formats (.MEM, .REC, .RMS, .POW)
Maximum loadable file size: Maximum file size that can be saved by
a given device (file size may be limited depending on the computer
configuration)
Data conversion
Conversion to CSV format, tab delimited, space delimited/data culling
(simple)/convert for specified channel/batch conversion of multiple files
Print functions
Print formatting (1 up, 2-to-16 up, 2-to-16 rows, X-Y 1-to-4 up) /preview/
hard copy functions usable on any printer supported by operating system
Other
Parameter calculation/search/clipboard copy/launching of other
applications