72" INDY FLUSH™ INDOOR / OUTDOOR LED FAN CEILING FAN INSTRUCTION MANUAL
WE WANT YOU TO LOVE YOUR NEW FAN SO WE’RE HERE IF YOU HAVE A QUESTION, NEED SOME HELP OR WANT TO CHAT ABOUT OUR PRODUCTS. SEND SUGGESTIONS OUR WAY TOO—WE’RE ALWAYS LOOKING TO MAKE YOUR EXPERIENCE WITH HINKLEY A POSITIVE ONE. > SERVICE@HINKLEY.COM > 800.HINKLEY > LET’S SEE THAT HINKLEY STYLE @HINKLEY #HINKLEYSTYLE This manual contains complete instructions for the installation and operation of this fan. It has been designed to make the installation process as easy as possible.
TABLE OF CONTENTS 02 GENERAL INSTALLATION & OPERATING INSTRUCTIONS 10 INSTALLING THE DECORATIVE COVER 03 IMPORTANT SAFETY PRECAUTIONS 11 INSTALLING THE WALL CONTROL 03 TOOLS & MATERIALS REQUIRED 13 OPERATING 04 UNPACKING YOUR FAN 15 CARE AND CLEANING 05 PREPARATION 15 TROUBLESHOOTING 05 INSTALLING THE HANGING BRACKET 16 ENERGY GUIDE 06 HANGING THE FAN 16 SPECIFICATIONS 07 ELECTRICAL CONNECTIONS 17 SMART BY BOND 08 FINISHING THE INSTALLATION 09 INSTALLING THE BLADES WARNIN
GENERAL INSTALLATION & OPERATION INSTRUCTIONS 1 To ensure the success of the installation, be sure to read the instructions and review the diagrams thoroughly before beginning. 2 To avoid possible electric shock, be sure electricity is turned off at the main power box before wiring. All electrical connections must be made in accordance with local codes, ordinances and/or the National Electric Code.
IMPORTANT SAFETY PRECAUTIONS WARNINGS: • Disconnect power by removing fuse or turning off circuit breaker before installing the fan and/or optional lighting. • Support directly from building structure. • To reduce the risk of fire, electric shock or personal injury, mount to outlet box marked "acceptable for fan support" and use mounting screws provided with the outlet box. Most outlet boxes commonly used for the support of lighting fixtures are not acceptable for fan support and may need to be replaced.
UNPACKING YOUR FAN UNPACK YOUR FAN AND CHECK THE CONTENTS. • Do not discard the carton. If warranty replacement or repair is ever necessary, the fan should be returned in original packing. Remove all parts and hardware. Do not lay motor housing on its side, or the decorative housing may shift, be bent or damaged. • Examine all parts.
PREPARATION PREPARATION: Verify you have all parts before beginning the installation. Check foam insert closely for missing parts. Remove motor from packing. To avoid damage to finish, assemble motor on soft padded surface or use the original foam inset in motor box. Motor Housing Decorate Cover DO NOT LAY MOTOR HOUSING ON ITS SIDE AS THIS COULD RESULT IN SHIFTING OF MOTOR IN DECORATIVE ENCLOSURE. Blade Parts identification on assembled fan.
INSTALLING THE FAN REMEMBER to turn off the power. Follow the steps below to hang your fan properly. Carefully lift fan motor assembly (without the blades) into position by hanging the motor assembly onto the hook from the ceiling adapter plate allowing it to hang freely. (Fig. 1) Outlet Box Fan Motor Fig. 1 INSTALLATION OF SAFETY CABLE SUPPORT Wood Ceiling Joist Attach the wood screw and the flat washer to the ceiling joist as shown (do not fully tighten).
ELECTRICAL CONNECTIONS REMEMBER -Turn off the power! NOTE - Control must be installed within 30 feet of fan. WARNINGS: Check to see that all connections are tight, including ground, and that no bare wire is visible at the wire nuts, except for the ground wire. Outlet box Black (hot) CAUTION: To reduce the risk of electric shock, this fan must be installed with an isolating wall control/switch.
FINISHING THE INSTALLATION 1 Remove the four washers and nuts from mounting bracker, move the motor into position over the four mounting studs and secure with the nuts and washers previously removed. (Fig. 1) 2 Raise the motor housing up against the mounting bracket, the four supports inside the motor housing should be placed against the four studs on mounting bracket, twist the motor housing clockwise until snug. (Fig. 2) Mounting studs Washers Mounting Bracket Nuts Motor Fig.
INSTALLING THE BLADES 1 Place blade over blade arm and align blade with mounting holes in blade arms. Repeat this procedure without tightening the screw until all 3 screws and nuts have been started into the blade arm. 2 Tighten each screw starting with center screw. 3 Fasten blade assembly to motor with provided screws and rubber washers by uses Blade Arm Wrench. Repeat procedure for remaining blades. Make sure screws are TIGHT! Loose motor screws can contribute to unnecessary hum during operation.
INSTALLATION THE DECORATIVE COVER NOTE: Mounting Hub Decorative Cover Fig. 1 10 | hinkley.com Be sure the power is off before installing. 1 Attach the lower cover to the mounting hub by turn the decorative cover clockwise until tight. 2 Turn the power on.
INSTALLING THE WALL CONTROL REMEMBER to turn off the power before you begin. NOTE - Secures to any surface or application: flat wall, single gang box, multi gang box. Option 2. For single gang box 1 Remove the existing wall plate and the old switch from the wall outlet box. 2 Seat the cradle A into the wall plate. (Fig. 2) 3 Connect the black lead wires from the switch in the cradle A to the black wires in the switch box. Hot input wire to one of the cradle A switch leads.
Option 3. Multi Gang Wall Switch Box Installation 1 Remove the existing wall plate and old switch from the wall outlet box. (Fig. 3) 2 Connect the black lead wires from the switch in the cradle A to the black wires in the switch box. Hot input wire to one of the cradle switch leads. Power lead to the fan is connected to the remaining switch lead. (Fig. 4) 3 Attach the cradle A to the wall switch box using the supplied hardware.
OPERATION This ceiling fan is equipped with an automatically learned type remote control. There is no frequency switches on the receiver or transmitter. The fan can start to use once the pairing process is done. Remove the panel from the transmitter and then install one 2032 battery (included). You need to use a coin to open or close the battery cover. To prevent damage to transmitter, remove the battery if not use for long periods of time (Fig. 1) WARNING: Chemical Burn Hazard.
Summer Mode and Winter Mode Operation 7 Summer Mode (forward): A DOWNWARD airflow creates a cooling effect as shown in Figure 3. This allows you to set your air conditioner on a warmer setting without affecting your comfort. 8 Winter Mode (Reverse): An UPWARD airflow moves warmer air off the ceiling area as shown in Figure 4. This allows you to set your heating unit on a cooler setting without affecting your comfort. SUMMER MODE (COUNTERCLOCKWISE DIRECTION) Fig. 3 14 | hinkley.
CARE AND CLEANING Periodically it may be necessary to re-tighten blade to blade arm screws or blade arm to motor screws to prevent clicking or humming sound during operation. This is especially true in climates with broad temperature and humidity ranges. When dusting the blades, you must support the blade to prevent bending - no pressure should be applied to the blades. If you experience any flaws in the operation of your fan, please check the following points.
ENERGY GUIDE SPECIFICATIONS AVERAGE PERFORMANCE AND ENERGY INFORMATION PERFORMANCE SPECIFICATIONS Estimated Yearly Energy Cost $6 $3 $34 Cost Range of Similar Models (19” – 84”) HIGH SPEED LOW SPEED Airflow (CFM) 6661 879 3,951 Energy Use (Watts) 31.8 2.2 Cubic Feet Per Minute Airflow Efficiency (CFM/W) 209 405 Energy Costs (Yearly) $6 $1 Amps 0.42 0.
SMART BY BOND (SOLD SEPARATELY) HINKLEY SMART FAN OPTIONS: In addition to the included wall control, you can control your Hinkley fan through the Bond app. • To use the app, download it for free from the App Store or Google Play. • Open the app to create your account. You can also login with your Facebook or Google account. • Next, set up a WiFi connection. You will need the SSID and WiFi password for the network you want to connect to.
HINKLEY IS PROUD TO PROVIDE YOU WITH CEILING FAN PRODUCTS THAT ENHANCE YOUR SPACE WITH COMFORT, PURPOSE AND STYLE. AS A FAMILY COMPANY, WE ARE COMMITTED TO DESIGN, PERFORMANCE AND QUALITY, AND WHAT’S IMPORTANT TO YOU IS PARAMOUNT TO US. FOR A COMPLETE ASSORTMENT OF OUR PRODUCTS AND SOURCE BOOKS, VISIT HINKLEY.COM.
GLOBAL HEADQUARTERS 33000 Pin Oak Parkway | Avon Lake, Ohio 44012 T (440) 653 5500 | F (440) 653 5555 | hinkley.
