Instructions / Assembly

Installation Instruction
 start here
Item No:
15300-LL
SAVE THESE INSTRUCTIO
Note: This Luminaire is designed for use with Hinkley approved 12 volt
landscape systems. Connection to other systems may cause premature
failure or non-intended operation.
LUMINAIRE MOUNTING: (for typical ground stake mounting)
1. To prevent electrical shock, disconnect transformer from electrical supply
before installation or service.
2. Run wire from Luminaire through mounting hole in top of ground stake.
3.
5.
Attach Luminaire to ground stake by threading to the mounting hole in stake
until it fits snuggly against the bottom of stem.
Place stake in desired position and insert into ground until the flange of stake
is flush with ground.
Strip the two wire leads from the Luminaire and connect to the main supply
wire using the provided wirenuts. It is recommended to add silicone to wire
nuts
Protected by routing in close proximity to the luminaire or fitting, or next to a
building structure such as a house or deck.
The main secondary wire is intended for shallow burial – less than 6 inches
(15.2cm)
- in order to connect to the main low voltage cable.
Have the length cut off so that it is connected to a connector within 6 inches
(15.2cm) from a building structure, a luminaire or fitting.

empezar aquí
Número
tierra)
superior de la estaca de tierra.
brida de estaca quede al ras con el suelo.
1.
Protegido por la ruta cerca de la luminaria o el accesorio, o al lado
de una estructura de edificio como una casa o una cubierta.
2.
El cable secundario principal está diseñado para enterramiento
superficial: menos de 6 pulgadas (15,2 cm)
- Para conectarse al cable principal de baja tensión.
3. Corte la longitud para que se conecte a un conector dentro de 6 pulgadas
(15,2 cm) de una estructura de edificio, una luminaria o un accesorio.
Instrucciones de Instalacion
:
Le câble principal basse tension du luminaire doit être
commencer ici
Número del
artículo:

del
actculo:
15300-LL
HH II NN KK LL EE YY
HINKLEY 33000 Pin Oak Parkway, Avon Lake, OH 44012 800.446.5539 / 440.653.5500 hinkley.com
15300-LL
ASSEMBLY INSTUCTIONS
El cable principal de baja tensión de la luminaria debe
estar
Silicone filled
Wire nut
Fixture Wire
Supply Wire
WIRING INSTUCTIONS
1 2
3 4
6
7
1. Lamp fixture using appropriate bulb (2)
2. Use lamp cover (3) to cover lamp (2)
3. Secure fixture cover (4) to the main body of
the fixture (1) using knobs (5+6). Note:
4. Secure ground spike (7
please make sure the knob (5) holding the
lamp cover is tightened to ensure bulb is
secure
) to the main body of
the fixture (1)
5. Fixture can now be powered on
1. Lámpara con bombilla adecuada (2)
2. Use la cubierta de la lámpara (3) para cubrir
la lámpara (2)
3. Asegure la cubierta de la lámpara (4) al
cuerpo principal de la lámpara (1) usando las
perillas (5). Nota: asegúrese de que la perilla
que sostiene la cubierta de la lámpara esté
apretada para garantizar que la bombilla esté
segura
4. Fije la pica de tierra (7) al cuerpo principal de
la luminaria (1)
5. Ahora se puede encender el dispositivo
1. Fixation de la lampe utilisant une ampoule
appropriée (2)
2. Utilisez le couvercle de la lampe (3) pour
couvrir la lampe (2)
3. Fixez le couvercle du luminaire (4) au corps
principal du luminaire (1) à l'aide des boutons
(5). Remarque : veuillez vous assurer que le
bouton tenant le couvercle de la lampe est
serré pour garantir que l'ampoule est
sécurisée.
4. Fixez le piquet de sol (7) au corps principal
du luminaire (1)
5. Le luminaire peut maintenant être allumé
5