Installation Sheet

assembly instructions

Item No. 3441

1. Find a clear area in which you can work.

3. Carefully review instructions prior to assembly.

start here

3441

Drawing 2 - Fixture Mounting

Drawing 3 - Glass Installation

Drawing 1 - Strap Detail

6.1.12

H I N K L E Y L I G H T I N G 33000 Pi n Oak Par kway Avon Lake , Ohio 44 012 800-44 6- 5539 www.hi nkl ey li ghti ng.com

shade

tab

2. Slip rubber washer (10) and thread on ring nut (11) onto center stem (3) to secure glass.

3. Thread thread decorative ball (12) onto center stem (3) and tighten.

4. Slip shade (13) over glass and set tabs inside shade onto top of glass. Center shade on glass.

L I G H T I N G

HINKLEYHINKLEY

T24 JA8-2016

1. To assemble main body of ﬁxture, ﬁrst thread hex nut (4) onto end of center stem (3)

approximately 3/8”.

2. Slip cap (2) onto end of center stem (3) and over the hex nut (4) added previously.

3. Thread the 3/8” of exposed thread of center stem (3) above cap (2) into coupler (1)

located in the center of the socket assembly.

4. Thighten hex nut (4) against cap (2) to secure center stem (3).

5. Slip tube (5) over center stem (3) followed by cap (6).

6. Slip steel washer (7) followed by rubber washer (8) onto end of center stem (3).

Fricition of rubber washer will hold parts in place. Fixture is ready for installation.

1. Prepare mounting strap (B) for mounting by installing screws (A) into mounting plate

(B) - see Drawing 1.

• Be sure the holes into which the screws are threaded match the spacing of holes (C) in

the canopy (D) - see Drawings 1 and 2.

2. Attach mounting plate (B) to junction box (J), using screws (G) provided and slip

supply wires through large center hole.

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18)

AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING

INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED

ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.

Make electrical connections from supply wire to ﬁxture lead wires. Refer to instruction

sheet (I.S. 18) and follow all instructions to make all necessary wiring connections.

1. Hang the ﬁxture by slipping canopy (D) over screws (A) and hold in position - see

Drawings 1 and 2.

2. Thread ball knobs (E) onto end of screws (A) and tighten to secure ﬁxture to ceiling.

PAGE 1
L I G H T I N 3441 HINKLEY assembly instructions G Item No. 3441 T24 JA8-2016 s tar t h ere Drawing 1 -Strap Detail J 1. Find a clear area in which you can work. 2. 3. Carefully review instructions prior to assembly. B - A G 1. To assemble main body of fixture, first thread hex nut (4) onto end of center stem (3) approximately 3/8”. Drawing 2 -Fixture Mounting 2. Slip cap (2) onto end of center stem (3) and over the hex nut (4) added previously. 3.
PAGE 2
L I G H T I N I.S. 18 wiring grounding instructions G I.S. 18 HINKLEY SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS. Drawing 1 - Flush Mount wiring instructions supply wire A C Indoor Fixtures E 1 2 twist-on connectors D B fixture leads 1.