Operating Instruction NUN 054 IE-A22 (01)
Table Of Contents
- Original operating instructions
- 1 Information about the documentation
- 2 Safety
- 3 Description
- 4 Technical data
- 5 Operation
- 5.1 Preparations at the workplace
- 5.2 Charging the battery
- 5.3 Inserting the battery
- 5.4 Removing the battery
- 5.5 Fitting the crimping / pressing or cutting jaws
- 5.6 Removing the crimping / pressing or cutting jaws
- 5.7 Inserting the crimping die (only for crimping jaws with crimping dies)
- 5.8 Removing the crimping die (only for crimping jaws with crimping dies)
- 5.9 Changing the cutting edges
- 5.10 Crimping
- 5.11 Making the cut
- 6 Care and maintenance
- 7 Transport and storage of cordless tools
- 8 Troubleshooting
- 9 Disposal
- 10 Manufacturer’s warranty
- 11 Further information
- Notice d'utilisation originale
- 1 Indications relatives à la documentation
- 2 Sécurité
- 3 Description
- 4 Caractéristiques techniques
- 5 Utilisation
- 5.1 Préparatifs
- 5.2 Recharge de l'accu
- 5.3 Introduction de l'accu
- 5.4 Retrait de l'accu
- 5.5 Mise en place de la pince à sertir ou à couper
- 5.6 Retrait des mors à sertir ou à couper
- 5.7 Mise en place de l'insert de sertissage (pince à sertir avec mors à sertir uniquement)
- 5.8 Retrait de l'insert de sertissage (pince à sertir avec mors à sertir uniquement)
- 5.9 Remplacement des lames de coupe
- 5.10 Faire le sertissage
- 5.11 Réalisation d'une coupe
- 6 Nettoyage et entretien
- 7 Transport et stockage des appareils sur accu
- 8 Aide au dépannage
- 9 Recyclage
- 10 Garantie constructeur
- 11 Informations complémentaires
- Manual de instrucciones original
- 1 Información sobre la documentación
- 2 Seguridad
- 3 Descripción
- 4 Datos técnicos
- 5 Manejo
- 5.1 Preparación del trabajo
- 5.2 Carga de la batería
- 5.3 Colocación de la batería
- 5.4 Extracción de la batería
- 5.5 Colocación de las mordazas de prensa o corte
- 5.6 Extracción de las mordazas de prensa o corte
- 5.7 Inserción del útil de prensado (solo para mordazas de prensa con útiles de prensado)
- 5.8 Extracción del útil de prensado (solo para mordazas de prensa con útiles de prensado)
- 5.9 Cambio de las hojas de corte
- 5.10 Ejecución de la operación de prensado (crimpado)
- 5.11 Ejecutar operación de corte
- 6 Cuidado y mantenimiento
- 7 Transporte y almacenamiento de las herramientas alimentadas por batería
- 8 Ayuda en caso de averías
- 9 Reciclaje
- 10 Garantía del fabricante
- 11 Más información
- Manual de instruções original
- 1 Indicações sobre a documentação
- 2 Segurança
- 3 Descrição
- 4 Características técnicas
- 5 Utilização
- 5.1 Preparação do local de trabalho
- 5.2 Carregar a bateria
- 5.3 Colocar a bateria
- 5.4 Retirar a bateria
- 5.5 Aplicar garras de aperto ou de corte
- 5.6 Retirar as garras de aperto ou de corte
- 5.7 Aplicar o caixilho de pressão (apenas para garras de aperto com caixilhos de pressão)
- 5.8 Retirar o caixilho de pressão (apenas para garras de aperto com caixilhos de pressão)
- 5.9 Substituir as lâminas de corte
- 5.10 Executar o processo de aperto (cravação)
- 5.11 Efectuar trabalho de corte
- 6 Conservação e manutenção
- 7 Transporte e armazenamento de ferramentas de baterias recarregáveis
- 8 Ajuda em caso de avarias
- 9 Reciclagem
- 10 Garantia do fabricante
- 11 Mais informações
8 English 2188463
*2188463*
5.7 Inserting the crimping die (only for crimping jaws with crimping dies) 4
WARNING
Risk of injury! Unintentional starting.
▶ Remove the battery before fitting, changing or removing the crimping / pressing die.
Never operate the tool without a crimping / pressing die in place.
1. Remove the battery.
2. Select a suitable crimping die. Push the two halves of the crimping / pressing die in until they engage.
5.8 Removing the crimping die (only for crimping jaws with crimping dies) 5
WARNING
Risk of injury! Unintentional starting.
▶ Remove the battery before fitting, changing or removing the crimping / pressing die.
1. Remove the battery.
2. Pull back the locking mechanism and remove the two halves of the crimping die.
5.9 Changing the cutting edges 6
WARNING
Risk of injury! Unintentional starting.
▶ Remove the battery before inserting, changing or removing cutting edges.
1. Remove the battery.
2. Unscrew the cutting edge securing screws.
3. Remove the cutting edges by pulling them out toward the front end of the tool.
4. Insert the new cutting edges in the tool.
5. Tighten the cutting edge securing screws.
5.10 Crimping 7
WARNING
Danger! Risk of fire due to faulty crimping.
▶ Use crimping terminals of the correct type and size for the cable and with the corresponding crimping
dies. Failure to observe this point can result in faulty crimping.
▶ Listen for the signal tone and check that the piston has retracted. If no signal tone is heard or if the piston
does not retract then the crimping is faulty.
1. Insert the connector in the open crimping die.
2. Press the control switch.
3. Keep the control switch pressed until the piston has retracted.
4. Repeat the crimping operation if necessary, beginning at A and moving in the direction of arrow B,
carrying out the number of crimping operations given in the tables.
5.11 Making the cut 8
WARNING
Risk of injury! Risk of serious injury during the cutting operation.
▶ Throughout the cutting operation, take great care to keep your hands and fingers well clear of the cutting
jaws.