Operating Instruction NUN 054 IE-A22 (01)
Table Of Contents
- Original operating instructions
- 1 Information about the documentation
- 2 Safety
- 3 Description
- 4 Technical data
- 5 Operation
- 5.1 Preparations at the workplace
- 5.2 Charging the battery
- 5.3 Inserting the battery
- 5.4 Removing the battery
- 5.5 Fitting the crimping / pressing or cutting jaws
- 5.6 Removing the crimping / pressing or cutting jaws
- 5.7 Inserting the crimping die (only for crimping jaws with crimping dies)
- 5.8 Removing the crimping die (only for crimping jaws with crimping dies)
- 5.9 Changing the cutting edges
- 5.10 Crimping
- 5.11 Making the cut
- 6 Care and maintenance
- 7 Transport and storage of cordless tools
- 8 Troubleshooting
- 9 Disposal
- 10 Manufacturer’s warranty
- 11 Further information
- Notice d'utilisation originale
- 1 Indications relatives à la documentation
- 2 Sécurité
- 3 Description
- 4 Caractéristiques techniques
- 5 Utilisation
- 5.1 Préparatifs
- 5.2 Recharge de l'accu
- 5.3 Introduction de l'accu
- 5.4 Retrait de l'accu
- 5.5 Mise en place de la pince à sertir ou à couper
- 5.6 Retrait des mors à sertir ou à couper
- 5.7 Mise en place de l'insert de sertissage (pince à sertir avec mors à sertir uniquement)
- 5.8 Retrait de l'insert de sertissage (pince à sertir avec mors à sertir uniquement)
- 5.9 Remplacement des lames de coupe
- 5.10 Faire le sertissage
- 5.11 Réalisation d'une coupe
- 6 Nettoyage et entretien
- 7 Transport et stockage des appareils sur accu
- 8 Aide au dépannage
- 9 Recyclage
- 10 Garantie constructeur
- 11 Informations complémentaires
- Manual de instrucciones original
- 1 Información sobre la documentación
- 2 Seguridad
- 3 Descripción
- 4 Datos técnicos
- 5 Manejo
- 5.1 Preparación del trabajo
- 5.2 Carga de la batería
- 5.3 Colocación de la batería
- 5.4 Extracción de la batería
- 5.5 Colocación de las mordazas de prensa o corte
- 5.6 Extracción de las mordazas de prensa o corte
- 5.7 Inserción del útil de prensado (solo para mordazas de prensa con útiles de prensado)
- 5.8 Extracción del útil de prensado (solo para mordazas de prensa con útiles de prensado)
- 5.9 Cambio de las hojas de corte
- 5.10 Ejecución de la operación de prensado (crimpado)
- 5.11 Ejecutar operación de corte
- 6 Cuidado y mantenimiento
- 7 Transporte y almacenamiento de las herramientas alimentadas por batería
- 8 Ayuda en caso de averías
- 9 Reciclaje
- 10 Garantía del fabricante
- 11 Más información
- Manual de instruções original
- 1 Indicações sobre a documentação
- 2 Segurança
- 3 Descrição
- 4 Características técnicas
- 5 Utilização
- 5.1 Preparação do local de trabalho
- 5.2 Carregar a bateria
- 5.3 Colocar a bateria
- 5.4 Retirar a bateria
- 5.5 Aplicar garras de aperto ou de corte
- 5.6 Retirar as garras de aperto ou de corte
- 5.7 Aplicar o caixilho de pressão (apenas para garras de aperto com caixilhos de pressão)
- 5.8 Retirar o caixilho de pressão (apenas para garras de aperto com caixilhos de pressão)
- 5.9 Substituir as lâminas de corte
- 5.10 Executar o processo de aperto (cravação)
- 5.11 Efectuar trabalho de corte
- 6 Conservação e manutenção
- 7 Transporte e armazenamento de ferramentas de baterias recarregáveis
- 8 Ajuda em caso de avarias
- 9 Reciclagem
- 10 Garantia do fabricante
- 11 Mais informações
*2188463*
2188463 English 7
5.2 Charging the battery
1. Before charging the battery, read the operating instructions for the charger.
2. Make sure that the contacts on the battery and the contacts on the charger are clean and dry.
3. Use an approved charger to charge the battery.
5.3 Inserting the battery
CAUTION
Risk of injury by short circuit or falling battery!
▶ Before inserting the battery, make sure that the contacts on the battery and the contacts on the product
are free of foreign matter.
▶ Make sure that the battery always engages correctly.
1. Charge the battery fully before using it for the first time.
2. Push the battery into the battery holder until it engages with an audible click.
3. Check that the battery is seated securely.
5.4 Removing the battery
1. Press the battery release buttons.
2. Remove the battery from the tool.
5.5 Fitting the crimping / pressing or cutting jaws 2
WARNING
Risk of injury! Unintentional starting.
▶ Remove the battery before fitting, changing or removing the crimping /pressing or cutting jaws.
Never operate the crimping / pressing tool without crimping / pressing or cutting jaws in place.
1. Remove the battery and select the most suitable crimping / pressing or cutting jaws.
2. Press the locking pins.
3. Rotate the locking pins counterclockwise as far as they will go.
4. Pull out the locking pins.
5. Fit the crimping / pressing or cutting jaws.
6. Push the locking pins in until they engage.
7. Rotate the tool head to the desired working position.
The tool head can be rotated much more easily when not under pressure.
5.6 Removing the crimping / pressing or cutting jaws 3
WARNING
Risk of injury! Unintentional starting.
▶ Remove the battery before fitting, changing or removing the crimping /pressing or cutting jaws.
1. Remove the battery and rotate the head of the tool to the outset position.
2. Press the locking pins.
3. Rotate the locking pins counterclockwise as far as they will go.
4. Pull out the locking pins.
5. Remove the crimping / pressing or cutting jaws toward the nose of the tool.