Operating Instruction SR 30-A36 (01)
Table Of Contents
- Original operating instructions
- Mode d'emploi original
- 1 Indications relatives à la documentation
- 2 Sécurité
- 2.1 Indications générales de sécurité pour les appareils électriques
- 2.2 Consignes de sécurité supplémentaires pour le sciage avec une lame de scie effectuant un mouvement de va-et-vient
- 2.3 Consignes de sécurité supplémentaires spécifiques aux scies
- 2.4 Consignes de sécurité supplémentaires
- 2.5 Utilisation et emploi soigneux des accus
- 3 Description
- 4 Caractéristiques techniques
- 5 Préparatifs
- 6 Utilisation
- 7 Nettoyage et entretien
- 8 Transport et stockage des outils sur accu et des accus
- 9 Aide au dépannage
- 10 Recyclage
- 11 Garantie constructeur
- Manual de instrucciones original
- 1 Información sobre la documentación
- 2 Seguridad
- 2.1 Indicaciones generales de seguridad para herramientas eléctricas
- 2.2 Indicaciones de seguridad adicionales para sierras con hojas de sierra de vaivén
- 2.3 Indicaciones de seguridad adicionales para el serrado
- 2.4 Indicaciones de seguridad adicionales
- 2.5 Manipulación y utilización segura de las baterías
- 3 Descripción
- 4 Datos técnicos
- 5 Preparación del trabajo
- 6 Manejo
- 7 Cuidado y mantenimiento
- 8 Transporte y almacenamiento de las baterías y sus herramientas
- 9 Ayuda en caso de averías
- 10 Reciclaje
- 11 Garantía del fabricante
- Manual de instruções original
8 English 2186518
*2186518*
5.1 Charging the battery
1. Before charging the battery, read the operating instructions for the charger.
2. Make sure that the contacts on the battery and the contacts on the charger are clean and dry.
3. Use an approved charger to charge the battery. → page 6
5.2 Inserting the battery
WARNING
Risk of injury by short circuit or falling battery!
▶ Before inserting the battery, make sure that the contacts on the battery and the contacts on the product
are free of foreign matter.
▶ Make sure that the battery always engages correctly.
1. Charge the battery fully before using it for the first time.
2. Push the battery into the product until it engages with an audible click.
3. Check that the battery is seated securely.
5.3 Removing the battery
1. Press the battery release buttons.
2. Remove the battery from the tool.
5.4 Installing the scaffold hook (accessory) 2
1. Engage the transport lock.
2. Install the scaffold hook.
5.5 Inserting the saw blade 3
Use only saw blades with a 1/2" connection end.
1. Activate the transport lock or separate the battery from the power tool.
2. Check that the connection end of the accessory tool is clean and lightly greased. Clean it and grease it if
necessary.
3. Push the locking lever up as far as it will go and hold it in this position.
4. Push the saw blade into the chuck from in front.
5. Allow the locking lever to return to its original position.
6. Grip and pull the saw blade to check that it is locked in position.
5.6 Installing the dust removal adapter (USA: accessory) 4
1. Pull the contact shoe out.
2. Set the dust removal adapter on the contact shoe mount.
3. Insert the lightly greased contact shoe fully into the guide.
6 Operation
Observe the safety instructions and warnings in this documentation and on the product.
6.1 Guiding the saw 5
1. Hold the saw by the grips provided for the purpose.
2. Guide the saw to the workpiece.
3. Guide the saw forward and back.
▶ If you press the saw against the workpiece there is a risk of the saw blade breaking and causing
injuries.