Operating Instruction AG 600-A36 (02)
Table Of Contents
- Original operating instructions
- 1 Information about the documentation
- 2 Safety
- 3 Description
- 4 Technical data
- 5 Before use
- 6 Operation
- 7 Care, maintenance, transport and storage
- 8 Troubleshooting
- 9 Disposal
- 10 Manufacturer’s warranty
- Mode d'emploi original
- 1 Indications relatives à la documentation
- 2 Sécurité
- 2.1 Indications générales de sécurité pour les appareils électriques
- 2.2 Consignes de sécurité générales pour le meulage, le ponçage au papier abrasif, les travaux avec des brosses métalliques, le polissage et le tronçonnage :
- 2.3 Consignes de sécurité supplémentaires
- 2.4 Utilisation et emploi soigneux des batteries
- 3 Description
- 3.1 Vue d'ensemble du produit
- 3.2 Utilisation conforme à l'usage prévu
- 3.3 Éléments livrés
- 3.4 Système de protection thermique du moteur
- 3.5 Carter de protection avec cache avant
- 3.6 Capot dépoussiéreur compact pour travaux de tronçonnage DC-EX 125/5 C (accessoire)
- 3.7 Capot dépoussiéreur (meulage) DG-EX 125/5 (accessoire)
- 3.8 Consommables
- 3.9 Indicateur de l'état de charge de l'accu Li-Ion
- 4 Caractéristiques techniques
- 5 Mise en service
- 5.1 Introduction de l'accu
- 5.2 Retrait de l'accu
- 5.3 Montage de la poignée latérale
- 5.4 Montage ou démontage du carter de protection
- 5.5 Montage ou démontage du cache avant
- 5.6 Positionnement du capot dépoussiéreur compact DC-EX 125/5 C
- 5.7 Montage ou démontage des outil amovibles
- 5.7.1 Montage de l'outil amovible
- 5.7.2 Démontage de l'outil amovible
- 5.7.3 Montage de l'outil amovible avec écrou à serrage rapide Kwik lock
- 5.7.4 Démontage de l'outil amovible avec écrou à serrage rapide Kwik lock
- 5.7.5 Montage de l'outil amovible avec filetage intégré
- 5.7.6 Démontage de l'outil amovible
- 6 Utilisation
- 7 Nettoyage, entretien, transport et entreposage
- 8 Aide au dépannage
- 9 Recyclage
- 10 Garantie constructeur
- Manual de instrucciones original
- 1 Información sobre la documentación
- 2 Seguridad
- 2.1 Indicaciones generales de seguridad para herramientas eléctricas
- 2.2 Indicaciones de seguridad generales para las aplicaciones de lijado, lijado con papel de lija, trabajos con cepillos de alambre, pulido y tronzado con muelas:
- 2.3 Indicaciones de seguridad adicionales
- 2.4 Manipulación y utilización segura de las baterías
- 3 Descripción
- 3.1 Vista general del producto
- 3.2 Uso conforme a las prescripciones
- 3.3 Suministro
- 3.4 Protección de la herramienta en función de la temperatura
- 3.5 Cubierta protectora con tapa delantera
- 3.6 Protector antipolvo para trabajos de tronzado DC-EX 125/5 C cubierta compacta (accesorio)
- 3.7 Protector antipolvo (lijado) DG-EX 125/5 (accesorios)
- 3.8 Material de consumo
- 3.9 Indicador del estado de carga de la batería de Ion-Litio
- 4 Datos técnicos
- 5 Puesta en servicio
- 6 Manejo
- 7 Cuidado, mantenimiento, transporte y almacenamiento
- 8 Ayuda en caso de averías
- 9 Reciclaje
- 10 Garantía del fabricante
- Manual de instruções original
- 1 Indicações sobre a documentação
- 2 Segurança
- 3 Descrição
- 3.1 Vista geral do produto
- 3.2 Utilização conforme a finalidade projectada
- 3.3 Incluído no fornecimento
- 3.4 Protecção da ferramenta dependente da temperatura
- 3.5 Resguardo do disco com tampa dianteira
- 3.6 Dispositivo de extracção de pó para trabalhos de corte DC-EX 125/5 C (acessório)
- 3.7 Dispositivo de extracção de pó (rebarbar) DG-EX 125/5 (acessório)
- 3.8 Consumíveis
- 3.9 Indicador do estado de carga da bateria de iões de lítio
- 4 Características técnicas
- 5 Antes de iniciar a utilização
- 6 Utilização
- 7 Conservação, manutenção, transporte e armazenamento
- 8 Ajuda em caso de avarias
- 9 Reciclagem
- 10 Garantia do fabricante
14 English 2106619
*2106619*
Trouble or fault Possible cause Action to be taken
The battery doesn’t engage
with an audible click.
The retaining lugs on the battery
are dirty.
▶ Clean the retaining lugs and refit
the battery.
1 LED blinks.
The power tool doesn’t run.
Low battery. ▶ Change the battery and charge
the empty battery.
The battery is too hot or too cold. ▶ Allow the battery to cool down
or warm up slowly to room
temperature.
All 4 LEDs blink.
The power tool doesn’t run.
The tool has been overloaded. ▶ Release the control switch and
then press it again. Then allow
the power tool to run under no
load for approx. 30 seconds.
The angle grinder or battery
gets very hot.
Electrical fault. ▶ Switch the power tool off im-
mediately, remove the battery,
keep it under observation, allow
it to cool down and contact Hilti
Service.
The tool does not achieve full
power.
A battery with inadequate capacity
was used.
Capacity: > 2.6 Ah
▶ Use a battery with adequate
capacity.
The motor has no braking
effect.
Low battery. ▶ Change the battery and charge
the empty battery.
The power tool was overloaded
briefly.
▶ Release the control switch and
then press it again.
9 Disposal
Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The
materials must be correctly separated before they can be recycled. In many countries, your old tools,
machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti representative
for further information.
Battery disposal
Improper disposal of batteries can result in health hazards from leaking gases or fluids.
▶ DO NOT send batteries through the mail!
▶ Cover the terminals with a non-conductive material (such as electrical tape) to prevent short circuiting.
▶ Dispose of your battery out of the reach of children.
▶ Dispose of the battery at your Hilti Store, or consult your local governmental garbage disposal or public
health and safety resources for disposal instructions.
▶ Do not dispose of power tools, electronic equipment or batteries as household waste!
10 Manufacturer’s warranty
▶ Please contact your local Hilti representative if you have questions about the warranty conditions.
Printed: 07.03.2018 | Doc-Nr: PUB / 5246614 / 000 / 01










