HSL4 EXPANSION ANCHOR Technical Datasheet Update: Jun-21
http://hilti.
http://hilti.to/traceable-fastener a) b) c) All data for static or seismic load cases given in this section according to ETA-19/0556, issued 2020-01-20. All data for fatigue relevant load cases given in this section according to ETA-19/0858, issued 2020-02-17. For more details on Technical Data according to ICC please consult the relevant HNA FTM.
http://hilti.
http://hilti.
http://hilti.to/traceable-fastener Seismic resistance (for a single anchor) All data in this section applies to: - Correct setting (See setting instruction) - No edge distance and spacing influence - Steel failure - Minimum base material thickness - Concrete C 20/25, fc = 20 N/mm2 - αgap = 0,5 Effective anchorage depth for seismic C2 a) Anchor size hef,1b) Eff. Anchorage depth hef [mm] 70 Anchor size hef,1 Eff.
http://hilti.to/traceable-fastener Effective anchorage depth for seismic C1 a) Anchor size hef,1b) Eff. Anchorage depth hef [mm] 60 Anchor size hef,1 Eff. Anchorage depth hef [mm] 100 a) b) M8 hef,2 80 M16 hef,2 125 hef,3 100 hef,3 150 hef,1 70 b) hef,1 125 M10 hef,2 90 M20 hef,2 155 hef,3 110 hef,3 185 hef,1 80 b) hef,1 150 M12 hef,2 105 M24 hef,2 180 hef,3 130 hef,3 210 HSL4-SK only available in sizes M8-M12, HSL4-B only available in sizes M12-M24 HSL4-SK can only be set in position 1.
http://hilti.to/traceable-fastener Fatigue resistance All data in this section applies to: - Correct setting using Hilti seismic filling set (See setting instruction) - No edge distance and spacing influence - Minimum base material thickness - Concrete C 20/25, fc = 20 N/mm2 - Only applicable to HSL4-G version Anchor size Eff.
http://hilti.
http://hilti.
http://hilti.to/traceable-fastener Setting information Setting positions a) a) HSL4-SK can only be set in position 1. Setting details for HSL4 Anchor version Nominal diameter of drill bit Max. cutting diameter of drill bit Max. diameter of clearance hole in the fixture Setting position Fixture thickness Effective fixture thickness Reduction of fixture thickness Effective anchorage depth Min. depth of drill hole Min.
http://hilti.to/traceable-fastener Setting details for HSL4-G Anchor version Nominal diameter of drill bit Max. cutting diameter of drill bit Max. diameter of clearance hole in the fixture Setting position Fixture thickness Effective fixture thickness Reduction of fixture thickness Effective anchorage depth Min. depth of drill hole Min. thickness of concrete member Width across flats Installation torque Anchor version Nominal diameter of drill bit Max. cutting diameter of drill bit Max.
http://hilti.to/traceable-fastener Setting details for HSL4-SK a) Anchor version Nominal diameter of drill bit Max. cutting diameter of drill bit Max. diameter of clearance hole in the fixture Top diameter of countersunk head in the fixture Bottom diameter of countersunk head in the fixture Height of the countersunk head in the fixture Min. Fixture thickness Effective anchorage depth Min. depth of drill hole Min.
http://hilti.
http://hilti.to/traceable-fastener Setting instructions *For detailed information on installation of each specific HSL4 version, see instruction for use given with the package of the product.
http://hilti.to/traceable-fastener Anchor torqueing for HSL4, HSL4-G, HSL-4-SK a) Use torque wrench HSL4-B Safety cap b) Machine torqueing: Only HSL4 and HSL4-G M8 to M16.
http://hilti.to/traceable-fastener Setting instructions *For detailed information on installation of HSL4-G version, see instruction for use given with the package of the product.
