SFC 18A SFC 22A English Printed: 27.07.
1 Information about the documentation 1.1 About this documentation • • • Read this documentation before initial operation or use. This is a is a prerequisite for safe, trouble-free handling and use of the product. Observe the safety instructions and warnings in this documentation and on the product. Always keep the operating instructions with the product and make sure that the operating instructions are with the product when it is given to other persons. 1.2 Product-dependent symbols 1.2.
▶ ▶ ▶ ▶ Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
Service ▶ Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. 2.2 Additional safety precautions for screwdrivers Personal safety ▶ Only use the product if it is in perfect working order. ▶ Never tamper with or modify the tool in any way. ▶ Use the auxiliary grip supplied with the tool. Loss of control can cause personal injury. ▶ Always hold the power tool with both hands on the grips provided.
3 Description 3.1 Overview 6 Printed: 27.07.
@ ; = % Keyless chuck & Control switch (with electronic speed control) ( ) + § Grip / Charge state and fault display (Li-ion battery) Torque and drilling mode selector ring 2-speed gear selector switch Forward / reverse selector switch with safety lock Lamp Belt hook (optional) Release buttons with additional function (charge status display activation) 3.2 Intended use The product described is a hand-held cordless drill / driver.
5 Operation 5.1 Inserting the battery CAUTION Risk of injury. The drill/driver may start inadvertently. ▶ Before fitting the battery, check that the drill/driver is switched off and that the switch safety lock is activated. CAUTION Electrical hazard. Dirty contacts may cause a short circuit. ▶ Before inserting the battery, check to ensure that the battery terminals and the contacts in the drill/driver are free from foreign objects. CAUTION Risk of injury.
5.3 Fitting the accessory tool 1. 2. 3. 4. Set the forward/reverse switch to the middle position or remove the battery from the power tool. Check that the connection end of the accessory tool is clean. Clean the connection end if necessary. Open the keyless chuck. Insert the accessory tool into the keyless chuck and then turn the chuck firmly by hand until tight and several clicks are heard. 5. Check that the accessory tool is held securely. 5.4 Removing the accessory tool 1.
5.10 Selecting the gear Select the gear. ▶ 5.11 Fitting the belt hook (optional) WARNING Risk of injury. A falling power tool may present a risk of injury to yourself and others. ▶ Check that the belt hook is fitted securely before beginning work. Note The belt hook allows the power tool to be attached to a belt worn by the operator. The belt hook can be fitted to allow attachment on the left or right side of the body. Fit the belt hook. ▶ 6 Troubleshooting 6.
Trouble or fault The power tool does not work. The power tool does not work and one LED flashes. The on/off button cannot be pressed, i.e. the button is locked. LED 1 flashes The battery runs down more quickly than usual. The battery does not engage with an audible double click. Possible cause Electrical fault. Action to be taken ▶ Remove the battery from the tool and contact Hilti Service. Low battery. ▶ Change the battery and charge the empty battery. The battery is too hot or too cold.
Printed: 27.07.2016 | Doc-Nr: PUB / 5293242 / 000 / 00 ** Hilti = registered trademark of Hilti Corp.
