SIW 22T-A 1/2" SIW 22T-A3/4" English Printed: 27.07.
1 Information about the documentation 1.1 About this documentation • • • Read this documentation before initial operation or use. This is a is a prerequisite for safe, trouble-free handling and use of the product. Observe the safety instructions and warnings in this documentation and on the product. Always keep the operating instructions with the product and make sure that the operating instructions are with the product when it is given to other persons. 1.2 Explanation of symbols used 1.2.
▶ Write down the serial number in the table below. You will be required to state the product details when contacting Hilti Service or your local Hilti organization to inquire about the product. Product information Type Generation: Serial no.: SIW 22T-A 1/2"| SIW 22T-A 3/ 4 01 2 Safety 2.1 General safety precautions for power tools ***** For internal use only ***** 27.07.2016 / 13:24:49 - H2\DOK-Projekt\System\SIW_22T-A-G1\ENU\SIW22TA_P3 WARNING! Read all safety precautions and other instructions.
▶ Keep cutting tools sharp and clean. Properly maintained tools with sharp cutting edges are less likely to jam and are easier to control. Using and handling the cordless power tool ▶ Use only the specified batteries in the power tools. Use of any other batteries may present a risk of injury and fire. ▶ Recharge the batteries only with the chargers specified by the manufacturer. A charger that is suitable for a certain type of battery may present a risk of fire when used with other types of battery.
***** For internal use only ***** 27.07.2016 / 13:24:49 - H2\DOK-Projekt\System\SIW_22T-A-G1\ENU\SIW22TA_P3 3 Description 3.1 Overview of the product 7 Printed: 27.07.
@ ; = % 3/4" square drive with through hole Forward / reverse selector switch with safety lock Control switch Light to illuminate the work area & ( ) + Belt hook (optional) Battery State of charge and fault display (Li-ion battery) Release button with additional function (state of charge display activation) 3.2 Intended use The product described is a hand-held cordless impact screwdriver. It is designed for tightening and releasing nuts, bolts, anchors and wood screws.
5.2 Setting forward or reverse rotation Note In the middle position, the forward / reverse selector switch serves as a safety lock. ▶ Set the forward / reverse selector switch to forward or reverse rotation. 5.3 Fitting the socket 1 SIW 22T-A /2" CAUTION Risk of injury! Risk of the tool falling. ▶ ▶ ▶ Use only accessory tools of the locking type, designed specifically for impact screwdrivers. Before use, make sure that the accessory tool is correctly fitted or positioned and securely engaged.
***** For internal use only ***** 27.07.2016 / 13:24:49 - H2\DOK-Projekt\System\SIW_22T-A-G1\ENU\SIW22TA_P3 1. Set the forward/reverse switch to the middle position or remove the battery from the power tool. 2. Align the hole in the socket with the retention ball on the square drive. 3. Fit the locking ring on the socket. ◁ The socket engages securely. 5.4 Fitting the socket 3 SIW 22T-A /4" CAUTION Risk of injury! Risk of the tool falling. ▶ ▶ ▶ 1. 2. 3. 4. 5.
5.5 Removing the socket 1 1. Set the forward/reverse switch to the middle position or remove the battery from the power tool. 2. Pull the accessory tool off the square drive. 5.6 Removing the socket 3 SIW 22T-A /4" 1. 2. 3. 4. 5. 6. Set the forward/reverse switch to the middle position or remove the battery from the power tool. Remove the O-ring from the groove in the socket. Pull out the locking pin. Remove the socket from the square drive spindle of the tool. Fit the locking pin.
• • Clean the air vents carefully with a dry brush. Use only a slightly damp cloth to clean the casing. Do not use cleaning agents containing silicone as these may attack the plastic parts. Care of the lithiumion batteries • Keep the battery free from oil and grease. • Use only a slightly damp cloth to clean the casing. Do not use cleaning agents containing silicone as these may attack the plastic parts. • Avoid ingress of moisture. ***** For internal use only ***** 27.07.
The tool doesn’t work – 1 LED blinks. The tool doesn’t work – 4 LEDs blink. The control switch cannot be pressed. Speed of rotation drops considerably. The battery is not heard to engage. The battery runs low more quickly than usual. The tool or the battery gets very hot. Possible cause The battery is not fitted correctly. Action to be taken ▶ 1 LED blinks: The battery is empty. ▶ The battery is too hot or too cold. ▶ The power tool was overloaded briefly.
Printed: 27.07.2016 | Doc-Nr: PUB / 5293233 / 000 / 00 ** Hilti = registered trademark of Hilti Corp.
