Use and Care Manual
Table Of Contents
- Original operating instructions
- 1 Information about the documentation
- 2 Safety
- 3 Description
- 4 Technical data
- 5 Preparations at the workplace
- 6 Operation
- 7 Care and maintenance
- 8 Transport and storage of cordless tools and batteries
- 9 Troubleshooting
- 10 Disposal
- 11 Manufacturer’s warranty
- 12 FCC statement (applicable in US) / IC statement (applicable in Canada)
- 13 Further information
- Notice d'utilisation originale
- 1 Indications relatives à la documentation
- 2 Sécurité
- 3 Description
- 4 Caractéristiques techniques
- 5 Préparatifs
- 6 Utilisation
- 7 Nettoyage et entretien
- 8 Transport et stockage des outils sur accu et des accus
- 9 Aide au dépannage
- 10 Recyclage
- 11 Garantie constructeur
- 12 Déclaration FCC (valable aux États-Unis) / Déclaration IC (valable au Canada)
- 13 Informations complémentaires
- Manual de instrucciones original
- 1 Información sobre la documentación
- 2 Seguridad
- 3 Descripción
- 4 Datos técnicos
- 5 Preparación del trabajo
- 6 Manejo
- 7 Cuidado y mantenimiento
- 8 Transporte y almacenamiento de las baterías y sus herramientas
- 9 Ayuda en caso de averías
- 10 Reciclaje
- 11 Garantía del fabricante
- 12 Indicación FCC (válida en EE. UU.)/indicación IC (válida en Canadá)
- 13 Más información
8 English 2330316
*2330316*
Fill level monitoring
LED shows: The automatic cut-out in wet mode is active.
▶ Empty the container and clean the sensors.
Air speed warning signal
LED shows: The air speed in the suction hose has dropped below 20 m/s.
▶ Follow the instructions in the "Troubleshooting" section.
In order to ensure that the acoustic warning is emitted correctly, the hose diameter setting must be
set to the diameter of the suction hose in use.
3.10 Filter cleaning
WARNING
Injury to respiratory system due to dust loading! System applications (particularly grinding, cutting and
slitting) and the SafeSet application can cause considerable dust loads.
▶ Operate the product in system applications and the SafeSet application only with automatic filter cleaning
activated.
The filter cleaning system functions only when a suction hose is connected.
The vacuum cleaner has manual and automatic filter cleaning that removes most of the dust adhering to the
filter element.
Automatic filter cleaning can be switched off by pressing the "Automatic filter cleaning" button and switched
back on by pressing the button again.
Status Meaning
LED lights.
The filter cleaning system is active.
LED doesn’t light.
The filter cleaning system is not active.
The filter cleaning system is activated automatically each time the vacuum cleaner is switched on.
The filter element is cleaned automatically by a blast of air (a pulsating noise is heard).
In order to maintain continuously high suction power, in system applications (especially grinding and
sanding, cutting and slitting) or when collecting large quantities of dust, automatic filter cleaning must
be activated.
Independently of automatic filter cleaning, you can clean the filter at any time by pressing the "Manual filter
cleaning" button.
Power cleaning: To achieve maximum power for filter cleaning, press the "Manual filter cleaning"
button while at the same time keeping the end of the hose closed.
4 Technical data
4.1 Product properties
VC 140-2-22
Weight
13 lb
(6 kg)
Dimensions (L × W × H)
8.5 in × 13.8 in × 15.7 in
(215 mm × 350 mm × 400 mm)
Max. volume flow rate (tur-
bine data)
142 CFM (67 ℓ/s)
Max. vacuum
2 psi
(17 kPa)
Container capacity
2 liq. gal
US
(8 ℓ)