Operating Instruction NCT IS 045-A22 (01)
Table Of Contents
- Original operating instructions
- 1 Information about the documentation
- 2 Safety
- 3 Description
- 4 Technical data
- 5 Preparations at the workplace
- 6 Operation
- 7 Care and maintenance
- 8 Transport and storage of cordless tools
- 9 Troubleshooting
- 10 Disposal
- 11 FCC statement (applicable in US) / IC statement (applicable in Canada)
- 12 Manufacturer’s warranty
- Mode d'emploi original
- 1 Indications relatives à la documentation
- 2 Sécurité
- 3 Description
- 4 Caractéristiques techniques
- 5 Préparatifs
- 6 Utilisation
- 7 Nettoyage et entretien
- 8 Transport et stockage des appareils sur accu
- 9 Aide au dépannage
- 10 Recyclage
- 11 Déclaration FCC (valable aux États-Unis) / Déclaration IC (valable au Canada)
- 12 Garantie constructeur
- Manual de instrucciones original
- 1 Información sobre la documentación
- 2 Seguridad
- 3 Descripción
- 4 Datos técnicos
- 5 Preparación del trabajo
- 6 Manejo
- 7 Cuidado y mantenimiento
- 8 Transporte y almacenamiento de las herramientas alimentadas por batería
- 9 Ayuda en caso de averías
- 10 Reciclaje
- 11 Indicación FCC (válida en EE. UU.) / indicación lC (válida en Canada)
- 12 Garantía del fabricante
- Manual de instruções original
- 1 Indicações sobre a documentação
- 2 Segurança
- 3 Descrição
- 4 Características técnicas
- 5 Preparação do local de trabalho
- 6 Utilização
- 7 Conservação e manutenção
- 8 Transporte e armazenamento de ferramentas de baterias recarregáveis
- 9 Ajuda em caso de avarias
- 10 Reciclagem
- 11 Declaração FCC / IC
- 12 Garantia do fabricante
*2258525*
2258525 English 7
5 Preparations at the workplace
CAUTION
Risk of injury by inadvertent starting!
▶ Before inserting the battery, make sure that the product is switched off.
▶ Remove the battery before making any adjustments to the power tool or before changing accessories.
Observe the safety instructions and warnings in this documentation and on the product.
5.1 Charging the battery
1. Before charging the battery, read the operating instructions for the charger.
2. Make sure that the contacts on the battery and the contacts on the charger are clean and dry.
3. Use an approved charger to charge the battery.
5.2 Inserting the battery
CAUTION
Risk of injury by short circuit or falling battery!
▶ Before inserting the battery, make sure that the contacts on the battery and the contacts on the product
are free of foreign matter.
▶ Make sure that the battery always engages correctly.
1. Charge the battery fully before using it for the first time.
2. Push the battery into the battery holder until it engages with an audible click.
3. Check that the battery is seated securely.
5.3 Removing the battery
1. Press the battery release buttons.
2. Remove the battery from the tool.
5.4 Assemble Hilti retaining leash (optional) 2
ATTENTION
Damage to the product and / or the retaining leash. Incorrect handling can result in damage to the
product and/or retaining leash.
▶ Do not use a metal chain as a retaining leash. Do not use retaining leashes longer than 6 ft (2 m).
To avoid damage and injury, when working at a height it is advisable to use the Hilti retaining strap.
The retaining strap allows a securing cord or leash to be attached.
When working with the product, you must comply with national regulations for working at heights.
1. Remove the battery.
2. Insert the two tabs on the retaining leash into the slots on each side of the base.
3. Secure the retaining leash with the screws supplied.
4. Refit the battery.
5.5 Dismantle the Hilti retaining leash (optional)
1. Remove the battery.
2. Remove the two retaining strap securing screws.
3. Pull the two retaining strap tabs out of the slots in the base and remove the retaining strap.
4. Refit the battery.
Printed: 14.08.2019 | Doc-Nr: PUB / 5509060 / 000 / 00