Operating Instruction NCT 85 C-22 (02)
Table Of Contents
- Original operating instructions
- Mode d'emploi original
- 1 Indications relatives à la documentation
- 2 Sécurité
- 3 Description
- 4 Caractéristiques techniques
- 5 Préparatifs
- 6 Utilisation
- 7 Nettoyage et entretien
- 8 Nettoyage et entretien
- 9 Transport et stockage des outils sur accu et des accus
- 10 Tableau des défaillances
- 11 Recyclage
- 12 Garantie constructeur
- 13 Informations complémentaires
- Manual de instrucciones original
- 1 Información sobre la documentación
- 2 Seguridad
- 3 Descripción
- 4 Datos técnicos
- 5 Preparación del trabajo
- 6 Manejo
- 7 Cuidado y mantenimiento
- 8 Cuidado y mantenimiento
- 9 Transporte y almacenamiento de las baterías y sus herramientas
- 10 Tabla de anomalías
- 11 Reciclaje
- 12 Garantía del fabricante
- 13 Más información
- Manual de instruções original
- 1 Indicações sobre a documentação
- 2 Segurança
- 3 Descrição
- 4 Características técnicas
- 5 Preparação do local de trabalho
- 6 Utilização
- 7 Conservação e manutenção
- 8 Conservação e manutenção
- 9 Transporte e armazenamento de ferramentas a bateria e baterias
- 10 Tabela de avarias
- 11 Reciclagem
- 12 Garantia do fabricante
- 13 Mais informações
8 English 2321716
*2321716*
4.1 Battery
Battery operating voltage
21.6 V
Weight, battery
See the end of these
operating instructions
Ambient temperature for operation
1 ℉ … 140 ℉
Storage temperature
−4 ℉ … 104 ℉
Battery charging starting temperature
14 ℉ … 113 ℉
5 Preparations at the workplace
WARNING
Risk of injury by inadvertent starting!
▶ Before inserting the battery, make sure that the product is switched off.
▶ Remove the battery before making any adjustments to the power tool or before changing accessories.
Observe the safety instructions and warnings in this documentation and on the product.
5.1 Charging the battery
1. Before charging the battery, read the operating instructions for the charger.
2. Make sure that the contacts on the battery and the contacts on the charger are clean and dry.
3. Use an approved charger to charge the battery. → page 6
5.2 Inserting the battery
WARNING
Risk of injury by short circuit or falling battery!
▶ Before inserting the battery, make sure that the contacts on the battery and the contacts on the product
are free of foreign matter.
▶ Make sure that the battery always engages correctly.
1. Charge the battery fully before using it for the first time.
2. Push the battery into the product until it engages with an audible click.
3. Check that the battery is seated securely.
5.3 Removing the battery
1. Press the battery release button.
2. Remove the battery from the product.
5.4 Switching starting lock on/off
The cutting tool has a starting lock that can be optionally activated or deactivated. If the starting lock is
activated, the control switch has to be pressed twice to start the cutting operation. This prevents inadvertent
starting.
The factory default is starting lock deactivated.
1. Remove the battery. → page 8
2. Press and hold down the control switch.
3. Insert the battery into the cutting tool.
4. Release the control switch.
▶ The green LED flashes twice; acoustic signal sounds twice: starting lock activated
▶ The green LED flashes twice; acoustic signal sounds once: starting lock deactivated