Operating Instruction NCR 120-22
Table Of Contents
- Original operating instructions
- 1 Information about the documentation
- 2 Safety
- 3 Description
- 4 Technical data
- 5 Preparations at the workplace
- 6 Operation
- 7 Care and maintenance
- 8 Transport and storage of cordless tools and batteries
- 9 Troubleshooting
- 10 Disposal
- 11 FCC statement (applicable in US) / IC statement (applicable in Canada)
- 12 Manufacturer’s warranty
- 13 Further information
- Mode d'emploi original
- 1 Indications relatives à la documentation
- 2 Sécurité
- 3 Description
- 4 Caractéristiques techniques
- 5 Préparatifs
- 6 Utilisation
- 7 Nettoyage et entretien
- 8 Transport et stockage des outils sur accu et des accus
- 9 Aide au dépannage
- 10 Recyclage
- 11 Déclaration FCC (valable aux États-Unis) / Déclaration IC (valable au Canada)
- 12 Garantie constructeur
- 13 Informations complémentaires
- Manual de instrucciones original
- 1 Información sobre la documentación
- 2 Seguridad
- 3 Descripción
- 4 Datos técnicos
- 5 Preparación del trabajo
- 6 Manejo
- 7 Cuidado y mantenimiento
- 8 Transporte y almacenamiento de las baterías y sus herramientas
- 9 Ayuda en caso de averías
- 10 Reciclaje
- 11 Indicación FCC (válida en EE. UU.) / indicación lC (válida en Canada)
- 12 Garantía del fabricante
- 13 Más información
- Manual de instruções original
- 1 Indicações sobre a documentação
- 2 Segurança
- 3 Descrição
- 4 Características técnicas
- 5 Preparação do local de trabalho
- 6 Utilização
- 7 Conservação e manutenção
- 8 Transporte e armazenamento de ferramentas a bateria e baterias
- 9 Ajuda em caso de avarias
- 10 Reciclagem
- 11 Declaração FCC / IC
- 12 Garantia do fabricante
- 13 Mais informações
*2321722*
2321722 English 9
5.1 Charging the battery
1. Before charging the battery, read the operating instructions for the charger.
2. Make sure that the contacts on the battery and the contacts on the charger are clean and dry.
3. Use an approved charger to charge the battery. → page 6
5.2 Inserting the battery
WARNING
Risk of injury by short circuit or falling battery!
▶ Before inserting the battery, make sure that the contacts on the battery and the contacts on the product
are free of foreign matter.
▶ Make sure that the battery always engages correctly.
1. Charge the battery fully before using it for the first time.
2. Push the battery into the product until it engages with an audible click.
3. Check that the battery is seated securely.
5.3 Removing the battery
1. Press the battery release button.
2. Remove the battery from the product.
5.4 Switching starting lock on/off
The crimping tool has a starting lock that can be optionally activated or deactivated. If the starting lock
is activated, the control switch has to be pressed twice to start the crimping operation. This prevents
inadvertent starting.
The factory default is starting lock deactivated.
1. Remove the battery. → page 9
2. Press and hold down the control switch.
3. Insert the battery into the crimping tool.
4. Release the control switch.
▶ The green LED flashes twice; acoustic signal sounds twice: starting lock activated
▶ The green LED flashes twice; acoustic signal sounds once: starting lock deactivated
5.5 Inserting crimping die 2
WARNING
Risk of injury! Unintentional starting.
▶ Remove the battery before inserting, changing or removing crimping dies.
Never operate the product without a crimping die installed!
1. Select suitable crimping dies.
2. Turn the crimping head so that the mount for the crimping dies is easily accessible.
3. Push the crimping dies in until they engage.
5.6 Removing crimping die 3
WARNING
Risk of injury! Unintentional starting.
▶ Remove the battery before inserting, changing or removing crimping dies.
1. Turn the crimping head so that the mount for the crimping dies is easily accessible.