Operating Instruction SC 30WR-22 (01)
Table Of Contents
- Original operating instructions
- Notice d'utilisation originale
- 1 Indications relatives à la documentation
- 2 Sécurité
- 3 Description
- 4 Caractéristiques techniques
- 5 Préparatifs
- 5.1 Recharge de l'accu
- 5.2 Introduction de l'accu
- 5.3 Retrait de l'accu
- 5.4 Montage de la lame de scie
- 5.5 Démontage de la lame de scie
- 5.6 Réglage de la profondeur de coupe
- 5.7 Réglage de l'angle de coupe
- 5.8 Montage de la butée parallèle
- 5.9 Monter l'adaptateur de rail de guidage
- 5.10 Montage du crochet pour échafaudages
- 6 Utilisation
- 7 Nettoyage et entretien
- 8 Transport et stockage des outils sur accu et des accus
- 9 Aide au dépannage
- 10 Recyclage
- 11 Garantie constructeur
- 12 Informations complémentaires
- Manual de instrucciones original
- 1 Información sobre la documentación
- 2 Seguridad
- 3 Descripción
- 4 Datos técnicos
- 5 Preparación del trabajo
- 5.1 Carga de la batería
- 5.2 Colocación de la batería
- 5.3 Extracción de la batería
- 5.4 Montaje de la hoja de sierra
- 5.5 Desmontaje de la hoja de sierra
- 5.6 Ajuste de la profundidad de corte
- 5.7 Ajuste del ángulo de corte
- 5.8 Montaje del tope paralelo
- 5.9 Montaje del adaptador del carril guía
- 5.10 Montaje del colgador de andamio
- 6 Manejo
- 7 Cuidado y mantenimiento
- 8 Transporte y almacenamiento de las baterías y sus herramientas
- 9 Ayuda en caso de averías
- 10 Reciclaje
- 11 Garantía del fabricante
- 12 Más información
- Manual de instruções original
- 1 Indicações sobre a documentação
- 2 Segurança
- 3 Descrição
- 4 Características técnicas
- 5 Preparação do local de trabalho
- 6 Utilização
- 7 Conservação e manutenção
- 8 Transporte e armazenamento de ferramentas a bateria e baterias
- 9 Ajuda em caso de avarias
- 10 Reciclagem
- 11 Garantia do fabricante
- 12 Mais informações
*2264108*
2264108 English 9
and the cutting width of the blade must be wider than the thickness of
the riving knife.
▶ Adjust the riving knife as described in this instruction manual.
Incorrect spacing, positioning and alignment can make the riving knife
ineffective in preventing kickback.
▶ Always use the riving knife except when plunge cutting. The riving
knife must be replaced after plunge cutting. The riving knife causes
interference during plunge cutting and can create kickback.
▶ For the riving knife to work, it must be engaged in the workpiece.
The riving knife is ineffective in preventing kickback during short cuts.
▶ Do not operate the saw if the riving knife is bent. Even a light
interference can slow the closing rate of a guard.
2.3 Additional safety instructions
Personal safety
▶ Never tamper with or modify the product or accessories in any way.
▶ Always hold the power tool with both hands on the grips provided.
Keep the grips dry, clean and free from oil and grease.
▶ Wear ear protectors. Exposure to noise can cause hearing loss.
▶ Respiratory protection must be worn if the power tool is used without
a dust removal system for work that creates dust.
▶ Operate the power tool only together with the safety devices that
belong to it.
▶ Improve the blood circulation in your fingers by relaxing your hands
and exercising your fingers during breaks between working.
▶ The power tool is not intended for use by inexperienced persons
who have received no special training.
▶ Keep the power tool out of reach of children.
▶ Do not switch the product on before it is at the workplace.
▶ Remove the battery before storing or transporting the power tool.
▶ Do not work overhead with the product.
▶ Do not attempt to brake the product by applying lateral pressure to
the saw blade.
▶ The path of the saw must be free of obstructions. Do not saw into
screws, nails etc.
▶ Do not touch the clamping flange or the clamping screw while the
power tool is running.
▶ Never press the drive spindle lock button while the saw blade is
rotating.
▶ Never direct the power tool toward persons.
▶ Adjust the pressure applied to the saw blade and the material being
cut so that the blade does not stall, possibly causing kickback.
▶ Avoid overheating the tips of the saw blade teeth.
▶ When cutting plastic, melting of the plastic should be avoided.