Use and Care Manual

3
Hilti Anchor Rod Specications and Technical Data
June 2018
HAS AND HIT-Z ANCHOR RODS
The following technical data is for HAS threaded rods and HIT-Z anchor rods available in the standard pre-cut rod program and the extended rod program.
Specifications and physical properties of Hilti HAS threaded rods and Hilti HIT-Z anchor rods
Threaded Rod Specification Units
Specified Ultimate
Strength,
f
uta
Minimum
Specified
Yield
Strength
0.2%
Offset, f
ya
f
uta
/ f
ya
Elongation,
Min. %
Reduction of Area,
Min. %
Specification for
Nuts and Washers
min. max.
5
CARBON STEEL
HAS-V-36 / HAS-V-36 HDG
ASTM F1554, Grade 36
1,2,8
psi 58,000 80,000 36,000
1.61 23 40
Nuts:
ASTM A194/194M, Grade 2H,
Heavy or ASTM A563-15 Grade C
Washers:
ASTM F436 Type 1
and ANSI B18.22.1 Type A Plain
(MPa) (400) (552) (248)
HAS-E-55 / HAS-E-55 HDG
ASTM F1554, Grade 55
1,2,8
psi 75,000 95,000 55,000
1.36 21
30 (3/8" - 2")
(MPa) (517) (655) (379) 22 (2-1/4" - 2-1/2")
HAS-B-105 / HAS-B-105 HDG
ASTM A193, Grade B7
1,3
ASTM F1554, Grade 105
1,2,8
psi 125,000
(6)
150,000 105,000
1.19
16 (B7) 50 (B7)
(MPa) (862)
(6)
(1,034) (724) 15 (Gr. 105) 45 (Gr. 105)
HIT-Z Anchor rod
(HIT-HY 200 only)
Unalloyed carbon steel
1
psi 94,200
NA
75,300
1.25 8 20
Nuts: ASTM A563 Gr. A
Washers: ASTM F844, HV
and ANSI B18.22.1 Type A Plain
(MPa) (650) (519)
STAINLESS STEEL
HAS-R 304 / 316
3/8-in. to 5/8-in. AISI Type 304 /
316 ASTM F 593 CW1
4
psi 100,000 150,000 65,000
1.54 20 -
Nuts:
ASTM F594
Washers:
ASTM A240 and
ANSI B18.22.1 Type A Plain
(MPa) (690) (1,034) (448)
HAS-R 304 / 316
3/4-in. to 1-in. AISI Type
304 / 316 ASTM F 593 CW2
4
psi 85,000 140,000 45,000
1.89 25 -
(MPa) (586) (966) (310)
HAS-R 304 / 316
1/4-in. and 1-1/8-in. to 2-in.
ASTM A193 Grade 8(M), Class 1
3
psi 75,000
(7)
NA
30,000
2.50
(7)
30 50
(MPa) (517)
(7)
(207)
HIT-Z-R Anchor rod
(HIT-HY 200 only)
Grade 316
psi 94,200
NA
75,300
1.25 8 20
(MPa) (650) (519)
1
All carbon steel threaded rods are zinc plated in accordance with ASTM F1941 Fe/Zn 5 AN, with nuts and washers zinc plated in accordance with ASTM B633 SC 1 Type III.
All hot-dipped galvanized threaded rods, nuts, and washers are zinc plated in accordance with ASTM F2329.
2
Standard Specication for Anchor Bolts, Steel, 36, 55, and 105-ksi Yield Strength.
3
Standard Specication for Alloy-Steel and Stainless Steel Bolting Materials for High-Temperature Service.
4
Standard Steel Specication for Stainless Steel Bolts, Hex Cap Screws, and Studs.
5
Maximum specied steel strength according to ASTM standard. NA indicates that ASTM standard does not publish a maximum value.
6
For designs according to CSA A23.3-14 Annex D, the maximum value of f
uta
is 860 MPa (124,700 psi) per clause D.6.1.2.
7
For calculating steel strength, ACI 318-14 section 17.4.1.2 and CSA A23.3-14 clause D.6.1.2 limit the ultimate strength to 1.9 f
ya
.
Thus, f
uta
= 57,000 psi (393 MPa) for calculation purposes when determining steel strength in tension (N
sa
) and shear (V
sa
).
8
3/8-inch dia. threaded rods are not included in the ASTM F1554 standard. Hilti 3/8-inch dia. HAS-V, HAS-E, and HAS-E-B (incl. HDG) threaded rods meet the chemical composition and mechanical
property requirements of ASTM F1554.