Operating Instruction SF 4-A22 (01)
Table Of Contents
- Original operating instructions
- 1 Information about the documentation
- 2 Safety
- 3 Description
- 4 Technical data
- 5 Operation
- 5.1 Charging the battery
- 5.2 Inserting the battery
- 5.3 Removing the battery
- 5.4 Fitting the belt hook (optional)
- 5.5 Installing Hilti bit holder (optional)
- 5.6 Hilti Installing the retaining strap (optional)
- 5.7 Fitting the accessory tool
- 5.8 Selecting the gear
- 5.9 Setting the torque
- 5.10 Setting forward or reverse rotation
- 5.11 Drilling
- 5.12 Screwdriving
- 6 Care and maintenance
- 7 Transport and storage
- 8 Troubleshooting
- 9 Disposal
- 10 Manufacturer’s warranty
- Mode d'emploi original
- 1 Indications relatives à la documentation
- 2 Sécurité
- 3 Description
- 4 Caractéristiques techniques
- 5 Utilisation
- 5.1 Recharge de l'accu
- 5.2 Introduction de l'accu
- 5.3 Retrait de l'accu
- 5.4 Montage de la patte d'accrochage (en option)
- 5.5 Montage du porte-embout Hilti (en option)
- 5.6 Montage de la sécurité anti-chute Hilti (en option)
- 5.7 Mise en place de l'outil amovible
- 5.8 Sélection de vitesse
- 5.9 Réglage du couple de rotation
- 5.10 Sélection du sens de rotation droite / gauche
- 5.11 Perçage
- 5.12 Vissages
- 6 Nettoyage et entretien
- 7 Transport et stockage
- 8 Aide au dépannage
- 9 Recyclage
- 10 Garantie constructeur
- Manual de instrucciones original
- 1 Información sobre la documentación
- 2 Seguridad
- 3 Descripción
- 4 Datos técnicos
- 5 Manejo
- 5.1 Carga de la batería
- 5.2 Colocación de la batería
- 5.3 Extracción de la batería
- 5.4 Montaje del colgador de cinturón (opcional)
- 5.5 Montaje del soporte para puntas de Hilti (opcional)
- 5.6 Montaje de la protección en caso de caída de Hilti (opcional)
- 5.7 Colocación del útil de inserción
- 5.8 Selección de la velocidad
- 5.9 Ajuste del par de giro
- 5.10 Ajuste del giro a la derecha o a la izquierda
- 5.11 Taladrado
- 5.12 Atornillado
- 6 Cuidado y mantenimiento
- 7 Transporte y almacenamiento
- 8 Ayuda en caso de averías
- 9 Reciclaje
- 10 Garantía del fabricante
- Manual de instruções original
- 1 Indicações sobre a documentação
- 2 Segurança
- 3 Descrição
- 4 Características técnicas
- 5 Utilização
- 5.1 Carregar a bateria
- 5.2 Colocar a bateria
- 5.3 Retirar a bateria
- 5.4 Montar o gancho de cinto (opcional)
- 5.5 Montar o suporte de bit Hilti (opcional)
- 5.6 Montar o dispositivo de segurança Hilti (opcional)
- 5.7 Colocar o acessório
- 5.8 Seleccionar a velocidade
- 5.9 Ajustar o torque
- 5.10 Ajustar a rotação à direita ou à esquerda
- 5.11 Perfurar
- 5.12 Aparafusar
- 6 Conservação e manutenção
- 7 Transporte e armazenamento
- 8 Ajuda em caso de avarias
- 9 Reciclagem
- 10 Garantia do fabricante
*2253605*
2253605 English 13
5.12 Screwdriving
1.
Set the function selector ring to the “screwdriving” position .
2. Set the torque setting ring to the desired torque.
3. Set the forward/reverse switch to the desired direction of rotation.
6 Care and maintenance
6.1 Care and maintenance
WARNING
Risk of injury with battery inserted !
▶ Always remove the battery before carrying out care and maintenance
tasks!
Care of the product
• Carefully remove stubborn dirt.
• Carefully clean the air vents, if present, with a dry, soft brush.
• Use only a slightly damp cloth to clean the housing. Do not use cleaning
agents containing silicone as these can attack the plastic parts.
• Use a dry, clean cloth to clean the contacts of the product.
Care of the Liion batteries
• Never use a battery with clogged air vents. Clean the air vents carefully
using a dry, soft brush.
• Avoid unnecessary exposure of the battery to dust and dirt. Never
expose the battery to high levels of moisture (e.g. by being dipped in
water or left in the rain).
If a battery has been soaked by moisture, treat it as a damaged battery.
Isolate it in a non-flammable container and consult Hilti Service.
• Keep the battery free of extraneous oil and grease. Do not permit dust
or dirt to accumulate unnecessarily on the battery. Clean the battery
with a dry, soft brush or a clean, dry cloth. Do not use cleaning agents
containing silicone as these can attack the plastic parts.
Do not touch the contacts of the battery and do not remove the factory-
applied grease from the contacts.
• Use only a slightly damp cloth to clean the housing. Do not use cleaning
agents containing silicone as these can attack the plastic parts.
Maintenance
• Check all visible parts and controls for signs of damage at regular
intervals and make sure that they all function correctly.
• Do not use the product if signs of damage are found or if parts
malfunction. Immediately have the product repaired by Hilti Service.
• After cleaning and maintenance, install all guards and protective devices
and check that they are in full working order.