Network Cube Camera Quick Start Guide 0
Network Cube Camera·Quick Start Guide Quick Start Guide © 2019 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. This Manual is the property of Hangzhou Hikvision Digital Technology Co., Ltd. or its affiliates (hereinafter referred to as “Hikvision”), and it cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision.
Network Cube Camera·Quick Start Guide TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS MANUAL AND THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, ARE PROVIDED “AS IS” AND “WITH ALL FAULTS AND ERRORS”. HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR OWN RISK.
Network Cube Camera·Quick Start Guide PARTIES, INCLUDING WITHOUT LIMITATION, RIGHTS OF PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, OR DATA PROTECTION AND OTHER PRIVACY RIGHTS. YOU SHALL NOT USE THIS PRODUCT FOR ANY PROHIBITED END-USES, INCLUDING THE DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES.
Network Cube Camera·Quick Start Guide encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help.
Network Cube Camera·Quick Start Guide designated collection points. For more information see: www.recyclethis.info 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg).
Network Cube Camera·Quick Start Guide Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
Network Cube Camera·Quick Start Guide Warnings Follow these safeguards to prevent serious injury or death. Cautions Follow these precautions to prevent potential injury or material damage. Warnings ● For device with this sticker, this device is intended for installation in a restricted access location, access can only be gained by service persons or by users who have been instructed about the reasons for the restrictions applied to the location and about any precautions that shall be taken.
Network Cube Camera·Quick Start Guide ● Please make sure that the plug is firmly connected to the power socket. When the product is mounted on wall or ceiling, the device shall be firmly fixed. ● If smoke, odor or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center. Cautions ● Make sure the power supply voltage is correct before using the camera. ● Do not drop the camera or subject it to physical shock.
Network Cube Camera·Quick Start Guide ● To avoid heat accumulation, good ventilation is required for operating environment. ● Keep the camera away from liquid while in use. ● While in delivery, the camera shall be packed in its original packing, or packing of the same texture. ● Regular part replacement: a few parts (e.g. electrolytic capacitor) of the equipment shall be replaced regularly according to their average enduring time.
Network Cube Camera·Quick Start Guide Table of Contents 1 Appearance Description ............................................................... 11 2 Notice ........................................................................................... 14 3 Installation .................................................................................... 16 3.1 Memory Card Installation .............................................. 16 3.2 Camera Mounting .........................................................
Network Cube Camera·Quick Start Guide 1 Appearance Description Appearance 1 4 6 2 3 7 5 11
Network Cube Camera·Quick Start Guide 10 11 8 9 12 Overview Description No.
Network Cube Camera·Quick Start Guide No. Description 9 Reset button 10 Alarm interface 11 Power interface 12 Speaker Note: Press RESET about 10s when the camera is power on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc.
Network Cube Camera·Quick Start Guide 2 Notice Do not install the camera in the extreme whether condition. Do not touch the lens with your finger. Do not install the camera towards the strong light or in the unstable lightening condition. Do not subject the camera to vibration, shock or heavy pressure.
Network Cube Camera·Quick Start Guide High humidity may damage the camera hardware; put it in dry and well-ventilated place. Under no circumstances should you submerge the camera in any type of liquid. Electromagnetic radiation may affect the video data transmission and the image quality. Do not install the camera near electromagnetic radiation source.
Network Cube Camera·Quick Start Guide 3 Installation Before you start: ● Make sure the device in the package is in good condition and all the assembly parts are included. ● The standard power supply is 12 VDC, please make sure your power supply matches with your camera. ● Make sure all the related equipment is power-off during the installation. ● Check the specification of the products for the installation environment.
Network Cube Camera·Quick Start Guide Steps: 1. Insert the memory card into the card slot on the side of the camera. 2. (Optional) Push the inserted memory card to get it sprung out. Memory Card Install Memory Card 3.2 Camera Mounting Steps: 1. Drill the screw holes according to the drill template. 44mm(1.73") Drill Template 2. Disassemble the bracket.
Network Cube Camera·Quick Start Guide 3. Install the fixed tray, base and camera to the mounting place in order.
Network Cube Camera·Quick Start Guide Wall Mounting 4. Adjust surveillance angel. 1). Loosen the adjusting knob 2 to adjust the panning position. 2). Loosen the adjusting knob 1 to adjust the tilting and rotation position. 3). After adjusting the angle of the camera to the desired position, fasten the two knobs.
Network Cube Camera·Quick Start Guide 4 Setting the Network Camera over the LAN Note: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, contact your dealer or the nearest service center for help. If your camera is used with HiLook NVR, refer to user manual of NVR for further operations.
Network Cube Camera·Quick Start Guide or tw Ne or Ne tw e abl kC 网络交换机 ork C abl e or Network Camera 半球 Computer Connect via a Switch or a Router Activate the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via web browser, activation via SADP, and activation via client software are all supported.
Network Cube Camera·Quick Start Guide The default IP address of the camera is 192.168.1.64. The computer and the camera should belong to the same subnet. For the camera enables the DHCP by default, you need to use the SADP software to search the IP address.
Network Cube Camera·Quick Start Guide 3. Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
Network Cube Camera·Quick Start Guide Select inactive device. Input and confirm password. SADP Interface Note: The SADP software supports activating the camera in batch. Refer to the user manual of SADP software for details. 3. Create and input the new password in the password field, and confirm the password.
Network Cube Camera·Quick Start Guide You can check whether the activation is completed on the popup window. If activation failed, make sure that the password meets the requirement and try again. Modify the IP Address Purpose: To view and configure the camera via LAN (Local Area Network), you need to connect the network camera in the same subnet with your PC. Use the SADP software or client software to search and change the IP address of the device.
Network Cube Camera·Quick Start Guide Modify the IP Address Note: You can enable the HiLookVision service for the device during activation. Refer to Chapter 6.1 for detailed information. 4. Input the admin password and click Modify to activate your IP address modification. The batch IP address modification is supported by the SADP. Refer to the user manual of SADP for details.
Network Cube Camera·Quick Start Guide 5 Access via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above version, Mozilla Firefox 5.0 and above version and Google Chrome 18 and above version Steps: 1. Open the web browser. 2.
Network Cube Camera·Quick Start Guide 4. Click Login. Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Follow the installation prompts to install the plug-in. Note: You may have to close the web browser to finish the installation of the plug-in. Download Plug-in 6. Reopen the web browser after the installation of the plug-in and repeat steps 2 to 4 to login.
Network Cube Camera·Quick Start Guide 6 Operate via HiLookVision App Purpose: HiLookVision is an application for mobile devices. With the App, you can view live image of the camera, receive alarm notification and so on. Note: HiLookVision service is not supported by certain camera models. Enable HiLookVision Service on Camera Purpose: HiLookVision service should be enabled on your camera before using the service. You can enable the service through SADP software or web browser.
Network Cube Camera·Quick Start Guide Verification Code Setting (SADP) Note: The verification code is required when you add the camera to HiLookVision app. 3. Click and read "Terms of Service" and "Privacy Policy". 4. Confirm the settings. Enable HiLookVision Service via Web Browser Before you start: You need to activate the camera before enabling the service. Refer to Chapter 4.2. Steps: 1. Access the camera via web browser. Refer to Chapter 5.
Network Cube Camera·Quick Start Guide 2. Enter platform access configuration interface: Configuration > Network > Advanced Settings > Platform Access. Platform Access Configuration (Web) 3. Select Platform Access Mode as HiLookVision. 4. Check the checkbox of Enable. 5. Click and read "Terms of Service" and "Privacy Policy" in pop-up window. 6. Create a verification code or change the verification code for the camera. Note: The verification code is required when you add the camera to HiLookVision app. 7.
Network Cube Camera·Quick Start Guide HiLookVision Setup Steps: 1. Download and install the HiLookVision app by searching "HiLookVision" in App Store or Google Play TM. 2. Launch the app and register for a HiLookVision user account. 3. Log in HiLookVision app after registration. Add Camera to HiLookVision Before you start: You need to enable the HiLookVision service on camera before adding it to your HiLookVision account. Refer to Chapter 6.1. Steps: 1.
Network Cube Camera·Quick Start Guide You can find the QR code on the camera or on the cover of the Quick Start Guide of the camera in the package. Figure 6-4 Scan QR Code Note: If the QR code is missing or too blur to be recognized, you can also add the camera by tapping the icon and inputting the camera's serial number. 3. Input the verification code of your camera. Note: ● The required verification code is the code you create or change when you enabling HiLookVision service on camera.
Network Cube Camera·Quick Start Guide Initialize the Memory Card Steps: Check the memory card status by tapping on the Storage Status in the Device Settings interface. If the memory card status displays as Uninitialized, tap to initialize it. The status will then change to Normal. You can then start recording any event triggered video in the camera such as motion detection.
UD09759B-B 0
