Hillstone A200 Series Hardware Reference Guide 1
Copyright 2021Hillstone Networks. All rights reserved. Information in this document is subject to change without notice. The software described in this document is furnished under a license agreement or nondisclosure agreement. The software may be used or copied only in accordance with the terms of those agreements.
Contents Contents ...................................................................................................................................... 3 Preface ......................................................................................................................................... 6 About This Manual ................................................................................................................ 6 Document Conventions .......................................................
Installation Devices/Tools/Cables ................................................................................... 17 Chapter 3 Installation .............................................................................................................. 18 Installing the Device on a Workbench.............................................................................. 18 Connecting Cables ...............................................................................................................
EU Conformity Statement ..................................................................................................
Preface About This Manual Thanks for choosing the network security products from Hillstone Networks. This document is an installation manual for the Hillstone A200Series device to help you install the device properly.
Chapter 1 Introduction Overview The A200 series equipment of Shanshi Netcom is the gateway equipment based on ARM architecture of Shanshi Netcom, which supports large capacity local. storageCurrently, A200-Series product models include A200、A200G4、A200G4B、A200W、A200WG4. Hardware Overview The size of A200 series equipment of Shanshi Netcom is 180 * 110 * 28mm, which belongs to desktop equipment and is used on the workbench.
Figure: A200G4Front Panel Power LED A200WG4 The front panel of 4G LED, 1 WLAN LED). Status LED 4G LED consists of several LED indicators (1 Power LED, 1 Status LED, 1 Figure: A200WG4Front Panel Power LED Status LED 4G LED WLAN LED Back Panel The A200 is powered by a power adapter, and the rear panel has a DC power interface, a CLR key, a USB interface, a con port, an SFP optical port, five Gigabit electrical ports, and a 4G antenna interface.
LED Color/Status Description STA Green/Blinking The system is running normally. Off The system has not been booted/is booting/has failed to boot. Green/Always on The device has detected a built-in WLAN module present. Green/Blinking WLAN is in data receiving and sending state Green/Always on The device has detected a built-in 4G module Green/Blinking 4G module is in data receiving and sending state. Green/Always on The link between this port and its peer device is in normal status.
Table: System Parameters Item Fixed Ports Description A200 Series 5 Gigabit port 1 USB 3.0 ports 1 CON port 1 SFP Smooth Mouth CPU 88f3720 Binuclear DDR4 SDRAM 2GB Flash Memory 4GB Dimensions (W×D×H) W180.0mm * D110.0mm *H28.0mm Weight Net weight: 0.64kg Gross weight:1.
Attribute Description Connector RJ-45 Port Standard RS-232C Baud Rate 115200 bit/s Services Connect the CON port to the serial port of a PC and run a terminal emulation program on the PC to configure the device Transmission Medium Console cable USB Port The A200-Series device provides up to 1 USB 2.0 host ports. Attributes for the USB host ports are shown in the table below: Table: USB 2.0 Host Port Attributes Attribute Description Connector USB Type-A interface Port Standard USB 2.
Table: SFP Port Attributes Attribute Description Connector SFP Frame Format Ethernet_II Ethernet_SNAP Negotiation Mode SFP optical module SFP copper module 1000Mbps 10/100/1000Mbps autosensing (some only supports 1000Mbps) Full/half-duplex The SFP port supports the following two types of modules: SFP optical module SFP copper module If an SFP optical module is applied to an SFP port, you should use a cable with a LC-type optical connector.
Attribute Description Short-haul Multimode Optical Module (850nm) Maximum Transmission Distance 0.
Attribute Description Maximum Transmission Distance 100m Negotiation Mode 10/100/1000Mbps autosensing (some only supports 1000Mbps) Full/half-duplex CLR Button The CLR button is the pinhole of the front panel and is used to reset the device back to the factory default settings. You can restore access to the device with this button if the login password is lost. Notes: Use this button with caution. Resetting the device will clear all existing configurations.
Chapter 2 Installation Preparations Introduction This chapter introduces the preparations before installing the Hillstone A200-Series device, including the installation site environment requirements. This chapter includes the following sections: Installation Site Environment Requirements The A200-Series device is designed for indoor use. To ensure the normal operation and to prolong the service lifetime, the installation site must meet the requirements below.
Take dustproof measures for the equipment room. Maintain proper humidity and temperature levels. Do not disassemble the device without permission from the vendor, or you may cause danger and void your warranty. EMI Prevention All possible Electromagnetic Interference (EMI) sources, external or internal, affect the device in the way of capacitance coupling, inductance coupling, electromagnetic radiation, and common impedance (including the grounding system) coupling.
Installation Devices/Tools/Cables The SG-6000A-Series device is shipped with a power cable and a console cable, and you should have the following items before the installation: 17 Terminal: Configuration terminal (e.g. an ordinary PC). Tools: Cross screwdriver and ESD wrist strap/antistatic gloves. Cables: Power cable, console cable and Ethernet cable.
Chapter 3 Installation A yellow seal with dark ink characters is stuck on a mounting screw of the chassis. Keep the seal intact. The sales representative will check this seal before maintenance operation. Please get the permission of your sales representative before opening the chassis yourself. Warranty will be void if you disassemble the chassis without authorization. Before installation, make sure that: The requirements in Chapter 2 Installation Preparations are satisfied.
Check the following specifications when installing the device on a workbench: Make sure the workbench is stable and well grounded. Make sure the intake and the exhaust vents are unblocked, and keep the device well ventilated. Do not place any heavy object on the top of the chassis. Connecting Cables The cable connection of A200 series equipment includes configuration cable connection, Ethernet cable connection and power cable connection..
Be careful not to connect the Ethernet port to the wrong ports. Read the label above the port carefully. For electrical Ethernet connection, use a crossover cable or straight-through cable. Connecting the Ethernet Fiber Cable Follow the guidelines below when connecting cables to the ports: Be careful not to connect the Ethernet port to the wrong ports. Read the label above the port carefully.
Figure: 4G Antenna take the following steps: 1. According to the function you use, select the corresponding antenna. 2. Install the antenna to the 4G SMA connector at the back panel of the device by rotating the antenna clockwise.
Note: Each type of antenna must be installed into the corresponding SMA connector. The 4G antenna must be installed into the connector of 4GDIV and 4GMAIN. The WLAN antenna must be installed into the connector of and . Installing the SIM Card To install the SIM card for A200 (4G\WLAN+4G version), take the following steps: 1. Purchase the SIM card from the ISP and activate the data connection service. 2. Insert the SIM card into the SIM card slot at the back panel of the device.
Chapter 4 Boot and Configuration Introduction This chapter describes how to perform initial system boot and basic configuration of the Hillstone A200-Series device, using a PC as the console terminal. Establishing a Configuration Environment The A200-Series device supports both local and remote configuration. Administrators can use the following configuration methods.
3. Switch on the power supply, and the device performs self-test and initializes the configuration automatically. If the booting succeeds, the system will display the command line prompt "login". Enter the default administrator name and password "hillstone" at the "login" and "password" prompts, press Enter. And now you are successfully logged in and accessing the CLI. After login, please change the default password of the device in time. 4. Enter commands to configure or view running status.
4. 5. Select the language you want to use. Click Login to enter the home page. After login, please change the default password of the device in time. Then you can set other configurations to the device. Telnet or SSH You can also establish Telnet and SSH configuration environments. For more information, see StoneOS CLI User Guide. Basic Configuration Before beginning to use the device, you should be familiar with its features and your network deployment.
Chapter 5 Hardware Maintenance and Replacement Introduction This chapter explains startup and shutdown methods of the Hillstone A200-Series device. Startup After being connected to the power supply by the power cord for the first time, the device will automatically start up. If the device is shut down by pressing the power button or using the shutdown command, and the power cord has not been disconnected after shutdown, you can press the power button to power on the device.
Chapter 6 Troubleshooting Introduction This chapter provides solutions to some common problems of the Hillstone A200-Series device. Losing the Administrator Password If you lose the administrator password, please contact your local sales representative or you can reset. Warning: when the system is reset, all device information will be restored to the factory settings, and the configuration file will be deleted. Please use it carefully.
Chapter 7 Addendum Statement Warning: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
est conforme aux limites d’exposition aux rayonnements d’Industrie Canada pour un environnement non contrôlé. EU Conformity Statement This product is marked with "CE" and comply therefore with the applicable harmonized European standards listed under the Radio Equipment Directive 2014/53/EU. This device has been tested and meets applicable limits for Radio Frequency (RF) exposure.
